TS912AIYD STMICROELECTRONICS [STMicroelectronics], TS912AIYD Datasheet

no-image

TS912AIYD

Manufacturer Part Number
TS912AIYD
Description
Rail-to-Rail CMOS Dual Operational Amplifier
Manufacturer
STMICROELECTRONICS [STMicroelectronics]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TS912AIYDT
Manufacturer:
SONY
Quantity:
6 238
Description
The TS912 is a rail-to-rail CMOS dual operational
amplifier designed to operate with a single or dual
supply voltage.
The input voltage range V
supply rails V
The output reaches:
This product offers a broad supply voltage
operating range from 2.7V to 16V and a supply
current of only 200µA/amp (V
Source and sink output current capability is
typically 40mA (at V
limitation circuit.
February 2006
Rail-to-rail input and output voltage ranges
Single (or dual) supply operation from 2.7V to
16V
Extremely low input bias current: 1pA typ.
Low input offset voltage: 2mV max.
Specified for 600Ω and 100Ω loads
Low supply current: 200µA/ampli
(V
Latch-up immunity
ESD tolerance: 3kV
Spice macromodel included in this specification
V
V
CC
CC
CC
-
-
+30mV, V
+300mV, V
= 3V)
CC
+
and V
CC
CC
CC
+
+
-40mV, with R
= 3V), fixed by an internal
CC
-400mV, with R
-
icm
.
includes the two
CC
= 3V).
Rail-to-Rail CMOS Dual Operational Amplifier
L
= 10kΩ
L
= 600Ω
Rev. 4
Pin connections (top view)
(Plastic Micropackage)
(Plastic Package)
DIP-8
SO-8
N
D
TS912
www.st.com
1/19
19

Related parts for TS912AIYD

TS912AIYD Summary of contents

Page 1

Rail-to-rail input and output voltage ranges ■ Single (or dual) supply operation from 2.7V to 16V ■ Extremely low input bias current: 1pA typ. ■ Low input offset voltage: 2mV max. ■ Specified for 600Ω and 100Ω loads ■ ...

Page 2

... Order Codes 1 Order Codes Part Number Temperature Range TS912IN TS912ID/IDT TS912AIN TS912AID/AIDT -40, +125°C TS912BID/BIDT TS912IYD/IYDT TS912AIYD/AIYDT 2/19 Package DIP8 SO-8 DIP8 SO-8 SO-8 SO-8 (automotive grade level) TS912 Packing Marking Tube TS912IN Tube or Tape & Reel 912I Tube TS912AIN 912AI 912BI Tube or Tape & Reel ...

Page 3

TS912 2 Absolute Maximum Ratings and Operating Conditions Table 1. Key parameters and their absolute maximum ratings Symbol V Supply voltage CC Vid Differential Input Voltage V Input Voltage i I Current on Inputs in I Current on Outputs o ...

Page 4

Typical Application Information 3 Typical Application Information Figure 1. Schematic diagram (1/2 TS912) p 4/19 p TS912 p ...

Page 5

Electrical Characteristics 4 Electrical Characteristics + Table 3V specified) Symbol Input Offset Voltage (V TS912A TS912B V io ≤ min. amb TS912A TS912B ∆V Input Offset Voltage Drift io Input Offset Current I ...

Page 6

Electrical Characteristics + Table 3V specified) Symbol φm Phase Margin en Equivalent Input Noise Voltage (R 1. Maximum values including unavoidable inaccuracies of the industrial test + Table 5V otherwise ...

Page 7

Electrical Characteristics + Table 5V otherwise specified) Symbol + SR Slew Rate ( Slew Rate (A en Equivalent Input Noise Voltage ( Channel Separation (f = 1kHz φm Phase ...

Page 8

Electrical Characteristics + Table 10V otherwise specified) Symbol Low Level Output Voltage ( 100kΩ 10kΩ 600Ω 100Ω L ≤ min. ...

Page 9

Electrical Characteristics Figure 2. Supply current (each amplifier) vs. supply voltage Figure 4. Low level output voltage vs. low level output current d Figure 6. High level output voltage vs. high level output current d P 9/19 Figure 3. High ...

Page 10

Electrical Characteristics Figure 8. Gain and phase vs. frequency W Figure 10. Phase margin vs. supply voltage W V Figure 12. Gain bandwidth product vs. supply voltage 10/19 Figure 9. Gain bandwidth product vs. supply voltage Figure ...

Page 11

Electrical Characteristics Figure 14. Input voltage noise vs. frequency 11/ TS912 ...

Page 12

Macromodels 5 Macromodels 5.1 Important note concerning this macromodel Please consider following remarks before using this macromodel. – All models are a trade-off between accuracy and complexity (i.e. simulation time). – Macromodels are not a substitute to breadboarding; rather, they ...

Page 13

Macromodels 13/ POSITIVE POWER SUPPLY * 5 NEGATIVE POWER SUPPLY .SUBCKT TS912_3 (analog) ***************************************************** ***** .MODEL MDTH D IS=1E-8 KF=6.564344E-14 CJO=10F * INPUT STAGE CIP 2 5 1.000000E-12 CIN 1 5 1.000000E-12 EIP ...

Page 14

Macromodels 5.4 Electrical characteristics from macromodelization Table 7. Electrical characteristics resulting from macromodel simulation connected Symbol 10kΩ load, per operator CC ...

Page 15

Macromodels 15/19 VIN 17 5 0.000000e+00 DINR 15 18 MDTH 400E-12 VIP 4 18 0.000000E+00 FCP 4 5 VOFP 5.750000E+00 FCN 5 4 VOFN 5.750000E+00 ISTB0 5 4 500N * AMPLIFYING STAGE FIP 5 19 VOFP 4.400000E+02 FIN 5 19 ...

Page 16

Package Mechanical Data 6 Package Mechanical Data In order to meet environmental requirements, ST offers these devices in ECOPACK interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with ...

Page 17

Package Mechanical Data 6.2 SO-8 Package DIM. MIN. A 1.35 A1 0.10 A2 1.10 B 0.33 C 0.19 D 4. 5.80 h 0.25 L 0.40 k ddd 17/19 SO-8 MECHANICAL DATA mm. TYP MAX. MIN. 1.75 ...

Page 18

Revision History 7 Revision History Table 8. Document revision history Date Revision Dec. 2001 1 July 2005 2 Oct. 2005 3 Feb. 2006 4 18/19 First Release 1 - PPAP references inserted in the datasheet see Table l: Key parameters ...

Page 19

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any ...

Related keywords