AT89C5131-PLTIL ATMEL Corporation, AT89C5131-PLTIL Datasheet - Page 143
AT89C5131-PLTIL
Manufacturer Part Number
AT89C5131-PLTIL
Description
8-bit Flash Microcontroller with Full Speed USB Device
Manufacturer
ATMEL Corporation
Datasheet
1.AT89C5131-PLTIL.pdf
(176 pages)
- Current page: 143 of 176
- Download datasheet (3Mb)
4136B–USB–09/03
Table 101. UEPINT Register
UEPINT (S:F8h read-only)
USB Endpoint Interrupt Register
Reset Value = 00h
Bit Number
7
-
7
6
5
4
3
2
1
0
Mnemonic Description
EP6INT
EP6INT
EP5INT
EP4INT
EP3INT
EP2INT
EP1INT
EP0INT
Bit
6
-
Reserved
The value read from this bit is always 0. Do not set this bit.
Endpoint 6 Interrupt
This bit is set by hardware when an interrupt is triggered by the (see Table 96 on
page 139) and this endpoint interrupt is enabled by the UEPIEN Register
UEPIEN (S:C2h) USB Endpoint Interrupt Enable Register (see Figure 102 on
page 144).
This bit is cleared by software.
Endpoint 5 Interrupt
This bit is set by hardware when an interrupt is triggered by the (see Table 96 on
page 139) and this endpoint interrupt is enabled by the UEPIEN Register
UEPIEN (S:C2h) USB Endpoint Interrupt Enable Register (see Figure 102 on
page 144).
This bit is cleared by software.
Endpoint 4 Interrupt
This bit is set by hardware when an interrupt is triggered by the (see Table 96 on
page 139) and this endpoint interrupt is enabled by the UEPIEN Register
UEPIEN (S:C2h) USB Endpoint Interrupt Enable Register (see Figure 102 on
page 144).
This bit is cleared by software.
Endpoint 3 Interrupt
This bit is set by hardware when an interrupt is triggered by the (see Table 96 on
page 139) and this endpoint interrupt is enabled by the UEPIEN Register
UEPIEN (S:C2h) USB Endpoint Interrupt Enable Register (see Figure 102 on
page 144).
This bit is cleared by software.
Endpoint 2 Interrupt
This bit is set by hardware when an interrupt is triggered by the (see Table 96 on
page 139) and this endpoint interrupt is enabled by the UEPIEN Register
UEPIEN (S:C2h) USB Endpoint Interrupt Enable Register (see Figure 102 on
page 144).
This bit is cleared by software.
Endpoint 1 Interrupt
This bit is set by hardware when an interrupt is triggered by the (see Table 96 on
page 139) and this endpoint interrupt is enabled by the UEPIEN Register
UEPIEN (S:C2h) USB Endpoint Interrupt Enable Register (see Figure 102 on
page 144).
This bit is cleared by software.
Endpoint 0 Interrupt
This bit is set by hardware when an interrupt is triggered by the (see Table 96 on
page 139) and this endpoint interrupt is enabled by the UEPIEN Register
UEPIEN (S:C2h) USB Endpoint Interrupt Enable Register (see Figure 102 on
page 144).
This bit is cleared by software.
EP5INT
5
EP4INT
4
EP3INT
3
EP2INT
2
AT89C5131
EP1INT
1
EP0INT
0
143
Related parts for AT89C5131-PLTIL
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-bit Flash Microcontroller With Full Speed Usb Device At89c5131
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: