EVAL-ADM1030 AD [Analog Devices], EVAL-ADM1030 Datasheet
EVAL-ADM1030
Related parts for EVAL-ADM1030
EVAL-ADM1030 Summary of contents
Page 1
... No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Evaluation Board for ACPI Temperature Monitor and PWM Fan Controller EVAL-ADM1030/31 THE ADM1030/31 The following is a brief description of the ADM1030/31 and a system overview. Further information can be found on the ADM1030 and ADM1031 datasheet ...
Page 2
... EVAL-ADM1030/ 55L Figure1. ADM1030 Evaluation Board Block Diagram ...
Page 3
... Figure2. ADM1031 Evaluation Board Picture –3– EVAL-ADM1030/ J7- ING O FF ...
Page 4
... EVAL-ADM1030/31 Figure3. ADM1030/31 Evaluation Board Schematic Preliminary Technical Data –4– REV. PrA ...
Page 5
... Preliminary Technical Data Figure3. ADM1030/31 Evaluation Board Schematic REV. PrA EVAL-ADM1030/31 –5– ...
Page 6
... EVAL-ADM1030/31 CONNECTORS AND SWITCHES AND INDICATORS The function of the various connectors, switches and indicators on the evaluation board are explained below. CENTRONICS CONNECTOR (J3) The evaluation board may be connected to the personal computer via the parallel printer port using the centronics cable provided. POWER CONNECTORS (J4 & J6) Power is supplied to the board via J6 using a 15V Power Supply mains adaptor ...
Page 7
... USB. However the USB option is not available on this revision of the evaluation board and so should not be selected. REV. PrA EVAL-ADM1030/31 Once the Communications medium has been selected, click on “Next” the next screen. When you are ready for the evaluation software to begin searching for the device on the chosen medium, click on “ ...
Page 8
... EVAL-ADM1030/31 If the ADM1030 or ADM1031 was not found on the chosen medium the following screen will appear. In this case check the connections to the board and the power supply. Then click on “Back” and try again. If this does not work then try re-booting the PC and re-running the software ...
Page 9
... Hex or decimal value in the text boxes of the Write display. The button will change from green to red and the new value can be written to the register by clicking on the red button. This is useful where a register contains a numeric value such as a temperature limit. Figure5 . ADM1030/31 Read/Write Program Tab –9– EVAL-ADM1030/31 ...
Page 10
... EVAL-ADM1030/31 VISUAL DISPLAY The visual display tab allows readings to be displayed graphically on bargraphs or line graphs. When the visual display is selected for the first time the value displayed on the bargraph is the value of local temperature. To display one of the other values e.g. remote temperature or fan speed click on the relevant bar graph button ...
Page 11
... ADM1031 for Fan2 also. 4. Click on “Enable Control” 5. Automatic Fan Speed Control is enabled using the user defined parameters. REV. PrA EVAL-ADM1030/31 FILTERED AUTOMATIC FAN SPEED CONTROL MODE. This mode is almost identical to the Automatic Fan Speed Control Mode. The main difference is the rate at which fan speed is ramped up after a temperature increase ...
Page 12
... EVAL-ADM1030/31 RPM CONTROL MODE In this method of control the user programs the required RPM values to the ADM1030/31. Click on the “RPM Feedback Mode” in the “Mode Select” window of the Control Tab. 1. Enter the required RPM Value in the window. 2. Choose which fan you wish to run at that RPM value. ...
Page 13
... This is achieved using the “Recall Previous Setup” Command. Click on “Recall Previous Setup” and choose the .txt filename of a previous set of register values. Then Click on “Open”. These previous values are written to the registers. REV. PrA EVAL-ADM1030/31 –13– ...
Page 14
... EVAL-ADM1030/31 APPENDIX A. COMPONENT LIST Capacitors C1-2, 0.01 F C3-4, C6, C7, C9 0.1 F C5, C8, C10 10 F Diodes D1, D2, D4 Red LED D 3 Green LED D 5 IN4001 Diode Connectors J1, J2, J8 3-pin Terminal Block J 3 Centronics Connector J 4 2-pin Terminal Block Barrell Connector J 7 CON\16 Header Resistors R1 R3, R5, R11, R13 ...