ADSP2115BSZ80

Manufacturer Part NumberADSP2115BSZ80
DescriptionQFP80
ManufacturerAnalog Devices
ADSP2115BSZ80 datasheet
 


Specifications of ADSP2115BSZ80

Date_code08+  
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
Page 7/64

Download datasheet (667Kb)Embed
PrevNext
The interrupt force and clear register, IFC, is a write-only
register that contains a force bit and a clear bit for each inter-
rupt (except for level-sensitive interrupts and the ADSP-2111
HIP interrupts—these cannot be forced or cleared in software).
When responding to an interrupt, the ASTAT, MSTAT, and
IMASK status registers are pushed onto the status stack and
the PC counter is loaded with the appropriate vector address.
The status stack is seven levels deep (nine levels deep on the
ADSP-2111) to allow interrupt nesting. The stack is automati-
cally popped when a return from the interrupt instruction is
executed.
Pin Definitions
Table IV (on next page) shows pin definitions for the ADSP-
21xx processors. Any inputs not used must be tied to V
Table III. Interrupt Vector Addresses & Priority
ADSP-2105
Interrupt
Source
RESET Startup
IRQ2
SPORT1 Transmit or IRQ1
SPORT1 Receive or IRQ0
Timer
ADSP-2101/2103/2115/216x
Interrupt
Source
RESET Startup
IRQ2
SPORT0 Transmit
SPORT0 Receive
SPORT1 Transmit or IRQ1
SPORT1 Receive or IRQ0
Timer
ADSP-2111
Interrupt
Source
RESET Startup
IRQ2
HIP Write from Host
HIP Read to Host
SPORT0 Transmit
SPORT0 Receive
SPORT1 Transmit or IRQ1
SPORT1 Receive or IRQ0
Timer
REV. B
SYSTEM INTERFACE
Figure 3 shows a typical system for the ADSP-2101, ADSP-
2115, or ADSP-2103, with two serial I/O devices, a boot
EPROM, and optional external program and data memory. A
total of 15K words of data memory and 16K words of program
memory is addressable for the ADSP-2101 and ADSP-2103. A
total of 14.5K words of data memory and 15K words of
program memory is addressable for the ADSP-2115.
Figure 4 shows a system diagram for the ADSP-2105, with one
serial I/O device, a boot EPROM, and optional external
program and data memory. A total of 14.5K words of data
memory and 15K words of program memory is addressable for
the ADSP-2105.
.
Figure 5 shows a system diagram for the ADSP-2111, with two
DD
serial I/O devices, a host processor, a boot EPROM, and
optional external program and data memory. A total of 15K
words of data memory and 16K words of program memory is
addressable.
Interrupt
Programmable wait-state generation allows the processors to
Vector Address
easily interface to slow external memories.
0x0000
The ADSP-2101, ADSP-2103, ADSP-2115, and ADSP-2111
0x0004 (High Priority)
processors also provide either: one external interrupt (IRQ2)
0x0010
and two serial ports (SPORT0, SPORT1), or three external
0x0014
interrupts (IRQ2, IRQ1, IRQ0) and one serial port (SPORT0).
0x0018 (Low Priority)
The ADSP-2105 provides either: one external interrupt (IRQ2)
and one serial port (SPORT1), or three external interrupts
(IRQ2, IRQ1, IRQ0) with no serial port.
Interrupt
Vector Address
Clock Signals
The ADSP-21xx processors’ CLKIN input may be driven by a
0x0000
crystal or by a TTL-compatible external clock signal. The
0x0004 (High Priority)
CLKIN input may not be halted or changed in frequency during
0x0008
operation, nor operated below the specified low frequency limit.
0x000C
If an external clock is used, it should be a TTL-compatible
0x0010
signal running at the instruction rate. The signal should be
0x0014
connected to the processor’s CLKIN input; in this case, the
0x0018 (Low Priority)
XTAL input must be left unconnected.
Because the ADSP-21xx processors include an on-chip oscilla-
Interrupt
tor circuit, an external crystal may also be used. The crystal
Vector Address
should be connected across the CLKIN and XTAL pins, with
two capacitors connected as shown in Figure 2. A parallel-
0x0000
resonant, fundamental frequency, microprocessor-grade crystal
0x0004 (High Priority)
should be used.
0x0008
0x000C
0x0010
0x0014
0x0018
0x001C
0x0020 (Low Priority)
–7–
ADSP-21xx
XTAL
CLKIN
CLKOUT
ADSP-21xx
Figure 2. External Crystal Connections