ATMEGA8515L8AU

Manufacturer Part NumberATMEGA8515L8AU
DescriptionTQFP44
ManufacturerATMEL Corporation
ATMEGA8515L8AU datasheet
 

Specifications of ATMEGA8515L8AU

Date_code10+  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
Page 181
182
Page 182
183
Page 183
184
Page 184
185
Page 185
186
Page 186
187
Page 187
188
Page 188
189
Page 189
190
Page 190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
Page 181/257

Download datasheet (3Mb)Embed
PrevNext
Latching of Fuses
Signature Bytes
Calibration Byte
2512J–AVR–10/06
Table 84. Fuse Low Byte
Fuse Low Byte
Bit no
Description
Brown-out Detector trigger
BODLEVEL
7
level
BODEN
6
Brown-out Detector enable
SUT1
5
Select start-up time
SUT0
4
Select start-up time
CKSEL3
3
Select Clock source
CKSEL2
2
Select Clock source
CKSEL1
1
Select Clock source
CKSEL0
0
Select Clock source
Notes:
1. The default value of SUT1..0 results in maximum start-up time. See Table 13 on page
39 for details.
2. The default setting of CKSEL3..0 results in internal RC Oscillator @ 1 MHz. See
Table 5 on page 35 for details.
The status of the Fuse bits is not affected by Chip Erase. Note that the Fuse bits are
locked if Lock bit1 (LB1) is programmed. Program the Fuse bits before programming the
Lock bits.
The fuse values are latched when the device enters Programming mode and changes of
the fuse values will have no effect until the part leaves Programming mode. This does
not apply to the EESAVE Fuse which will take effect once it is programmed. The fuses
are also latched on Power-up in Normal mode.
All Atmel microcontrollers have a 3-byte signature code which identifies the device. This
code can be read in both Serial and Parallel mode, also when the device is locked. The
three bytes reside in a separate address space.
For the ATmega8515 the signature bytes are:
1. $000: $1E (indicates manufactured by Atmel).
2. $001: $93 (indicates 8KB Flash memory).
3. $002: $06 (indicates ATmega8515 device when $001 is $93).
The ATmega8515 stores four different calibration values for the internal RC Oscillator.
These bytes resides in the signature row high byte of the addresses 0x000, 0x0001,
0x0002, and 0x0003 for 1, 2, 4, and 8 MHz respectively. During Reset, the 1 MHz value
is automatically loaded into the OSCCAL Register. If other frequencies are used, the
calibration value has to be loaded manually, see “Oscillator Calibration Register – OSC-
CAL” on page 39 for details.
ATmega8515(L)
Default value
1 (unprogrammed)
1 (unprogrammed, BOD
disabled)
(1)
1 (unprogrammed)
(1)
0 (programmed)
(2)
0 (programmed)
(2)
0 (programmed)
(2)
0 (programmed)
(2)
1 (unprogrammed)
181