PIC16F684-ISL

Manufacturer Part NumberPIC16F684-ISL
ManufacturerMicrochip Technology Inc.
PIC16F684-ISL datasheets
 


Specifications of PIC16F684-ISL

CaseN/ANotesNEW
Date_code11+  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
Page 101
102
Page 102
103
Page 103
104
Page 104
105
Page 105
106
Page 106
107
Page 107
108
Page 108
109
Page 109
110
Page 110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
Page 107/164

Download datasheet (3Mb)Embed
PrevNext
12.6
Watchdog Timer (WDT)
For PIC16F684, the WDT has been modified from
previous PIC16 devices. The new WDT is code and
functionally compatible with previous PIC16 WDT
modules and adds a 16-bit prescaler to the WDT. This
allows the user to have a scaler value for the WDT and
TMR0 at the same time. In addition, the WDT time-out
value can be extended to 268 seconds. WDT is cleared
under certain conditions described in Table 12-7.
12.6.1
WDT OSCILLATOR
The WDT derives its time base from the 31 kHz
LFINTOSC. The LTS bit does not reflect that the
LFINTOSC is enabled.
The value of WDTCON is ‘---0 1000’ on all Resets.
This gives a nominal time base of 16 ms, which is
compatible with the time base generated with previous
PIC16 microcontroller versions.
Note:
When the Oscillator Start-up Timer (OST)
is invoked, the WDT is held in Reset,
because the WDT Ripple Counter is used
by the OST to perform the oscillator delay
count. When the OST count has expired,
the WDT will begin counting (if enabled).
FIGURE 12-9:
WATCHDOG TIMER BLOCK DIAGRAM
16-bit WDT Prescaler
31 kHz
LFINTOSC Clock
WDTE from the Configuration Word Register
SWDTEN from WDTCON
Note 1: This is the shared Timer0/WDT prescaler. See Section 5.4 “Prescaler” for more information.
TABLE 12-7:
WDT STATUS
Conditions
WDTE = 0
CLRWDT Command
Oscillator Fail Detected
Exit Sleep + System Clock = T1OSC, EXTRC, INTRC, EXTCLK
Exit Sleep + System Clock = XT, HS, LP
 2004 Microchip Technology Inc.
A new prescaler has been added to the path between
the INTRC and the multiplexers used to select the path
for the WDT. This prescaler is 16 bits and can be
programmed to divide the INTRC by 32 to 65536,
giving the WDT a nominal range of 1 ms to 268s.
12.6.2
WDT CONTROL
The WDTE bit is located in the Configuration Word
register. When set, the WDT runs continuously.
When the WDTE bit in the Configuration Word register
is set, the SWDTEN bit (WDTCON<0>) has no effect.
If WDTE is clear, then the SWDTEN bit can be used to
enable and disable the WDT. Setting the bit will enable
it and clearing the bit will disable it.
The PSA and PS<2:0> bits (OPTION_REG) have the
same function as in previous versions of the PIC16
Family of microcontrollers. See Section 5.0 “Timer0
Module” for more information.
0
From TMR0 Clock Source
1
PSA
WDTPS<3:0>
Preliminary
PIC16F684
(1)
Prescaler
8
PS<2:0>
TO TMR0
1
0
PSA
WDT Time-out
WDT
Cleared
Cleared until the end of OST
DS41202C-page 105