AT-240160BFIQY-52H-A ZETTLER [ZETTLER Electronics], AT-240160BFIQY-52H-A Datasheet
AT-240160BFIQY-52H-A
Related parts for AT-240160BFIQY-52H-A
AT-240160BFIQY-52H-A Summary of contents
Page 1
... SPECIFICATIONS FOR LCD MODULE CUSTOMER CUSTOMER PART NO. AMPIRE PART NO. APPROVED BY DATE Approved For Specifications Approved For Specifications & Sample APPROVED BY Date : 2005/1/26 AT-240160BFIQY-52H-A CHECKED BY AMPIRE CO., LTD. ORGANIZED BY 1 ...
Page 2
... Revision Date Section 2005/1/26 Date : 2005/1/26 RECORD OF REVISION Contents - New Release AMPIRE CO., LTD. Editor Kokai 2 ...
Page 3
... FEATURES (1) Display format : 240 × 160 dot-matrix (2) Construction : LCD , TAB IC, Yellow-green edge LED backlight, Bazel and PCB. (3) Display type : FSTN, Transflective , 6 o’clock view. (4) Controller : SED1335F0B ; 32K SRAM. (5) 5V single power input. Built-in DC/DC converter for LCD driving. (6) Built-in Temperature compensation circuit. ...
Page 4
... I LED LED backlight Contrast CR Rise Time Tr Fall Time Tf θf θb Viewing Angle Range θl θr Frame Frequency fF Forward Voltage VF Forward Current IF LCM Luminous intensity Date : 2005/1/26 Condition Min ----- Electronic Characteristics ----- -- 4.5 20.0 -20°C 17.81 25°C 14.9 70°C -- 0.8 VDD -- VSS VDD = 5V -- LEDA = 5V -- ----- Optical Characteristics ----- 2 25°C -- 25° ...
Page 5
... LED Dice number = 2x5=10 LED Driving Circuit: (NOTE 1) Contrast ratio : CR = (Brightness in OFF state) / (Brightness in ON state) Date : 2005/1/26 A 240160BL Yellow-green LED AMPIRE CO., LTD ...
Page 6
... NOTE 2 ) Response time : (NOTE 3) Viewing angle Date : 2005/1/26 AMPIRE CO., LTD. 6 ...
Page 7
... BLOCK DIAGRAM From MPU FLM /RESET /RD LP, M, /DISPOFF Controller /WR SED1335 /CS A0 DB0~7 SRAM LED_ON 6 POWER SUPPLY CIRCUIT VDD Date : 2005/1/26 COM. Driver CP,D0~D3 LED Backlight 21.4V DC/DC Converter Bias & LCD Bias Temperature Circuit compensation circuit AMPIRE CO., LTD. LCD Panel 160 240 x 160 Dots 240 SEG ...
Page 8
... Series: Read Signal H/L 68 Series: Enable Signal(E) 80 Series: Write Signal H/L 68 Series: R/W Signal H/L Chip Select Signal H/L Data Type Selection H/L Data Input(8 bits) - Power Supply for Logic(+5.0V) - Power Supply(Ground : 0V) - Positive voltage output (+21.4V) Contrast Adjustment Input ( VADJ-VSS = LCD driving voltage ) H/L LED On/Off Signal; H: LED On L: LED Off ...
Page 9
... Data Hold Time /RD Access Time Output Disable Time Note: For memory control and system control commands: tCYC8=2tC+tOC+tCEA+75 > tACV +245 For all other commands: tCYC8=4tC+tOC+30 A0,/CS /WR,/RD DB0~DB7 (Write) DB0~DB7 (Read) Date : 2005/1/26 Condition Symbol tAH8 tAW8 tCYC CL=100 pF tOC VDD=2.7~4.5 tDS8 tDH8 tACC8 tOH8 AMPIRE CO ...
Page 10
... Access Time Enable Pulsewidth Note: For memory control and system control commands: tCYC6=2tC+tEW+tCEA+75 > tACV +245 For all other commands: tCYC6=4tC+tEW+30 E R/W A0, /CS DB0~DB7 (Write) DB0~DB7 (Read) Date : 2005/1/26 Condition Symbol tCYC6 tAW6 tAH6 CL=100 pF tDS6 VDD=2.7~4.5 tDH6 tOH6 tACC6 tEW AC Electrical Characteristics AMPIRE CO ...
Page 11
... CSRW, CSRR: Each byte is processed individually. The microprocessor may read or write just the low byte of the cursor address ...
Page 12
... INNER DATA FORMAT SEG1 # #160 COM1 # #240 D0 Date : 2005/1/ Landscape Display Type(Top View) ...
Page 13
... ACCEPTABLE QUALITY LEVEL A major defect is defined as one that could cause failure to or materially reduce the usability of the unit for its intended purpose. A minor defect is one that does not materially reduce the usability of the unit for its intended purpose infringement from established standards and has no significant bearing on its effective use or operation ...
Page 14
... INSPECTION QUALITY CRITERIA Item Description of defects Function Short circuit or Pattern cut Dimension Deviation from drawings Black spots Ave . dia . D D≦0.2 0.2<D≦0.3 0.3<D≦0.4 0.4<D Black lines Width W, Length L W≦0.03 0.03<W≦0.05 0.05<W≦0.07 , L≦3.0 See line criteria Bubbles in Average diameter D 0.2 < D < 0.5 mm polarizer for > ...
Page 15
... High Temperature Storage Low Temperature Storage Temperature Cycle Humidity Test Vibration Test (Packing) Note 1 : Condensation of water is not permitted on the module. Note 2 : The module should be inspected after 1 hour storage in normal conditions (15-35°C , 45-65%RH). Definitions of life end point : Current drain should be smaller than the specific value. ...
Page 16
... Do not modify the display PCB in either shape or positioning of components. (5) Do not modify or move location of the zebra or heat seal connectors. (6) The device should only be soldered to during interfacing. Modification to other areas of the board should not be carried out. (7) In the event of LCD breakage and resultant leakage of fluid do not inhale, ingest or make contact with the skin ...
Page 17
... OUTLINE DIMENSION Date : 2005/1/26 AMPIRE CO., LTD. 17 ...
Page 18
... Date : 2005/1/26 AMPIRE CO., LTD. 18 ...