ICX274 SONY [Sony Corporation], ICX274 Datasheet - Page 19
ICX274
Manufacturer Part Number
ICX274
Description
Diagonal 8.923mm (Type 1/1.8) Progressive Scan CCD Image Sensor with Square Pixel for Color Cameras
Manufacturer
SONY [Sony Corporation]
Datasheet
1.ICX274.pdf
(72 pages)
- Current page: 19 of 72
- Download datasheet (929Kb)
4. Video signal shading
5. Uniformity between video signal channels
6. Dark signal
7. Dark signal shading
8. Line crawl
9. Lag
Set to the standard imaging condition II. With the lens diaphragm at F5.6 to F8, adjusting the luminous
intensity so that the average value of the G channel signal output is 150mV. Then measure the maximum
value (Gmax [mV]) and minimum value (Gmin [mV]) of the G signal output and substitute the values into
the following formula.
SH = (Gmax – Gmin)/150
After measuring 4, measure the maximum (Rmax [mV]) and minimum (Rmin [mV]) values of the R signal
and the maximum (Bmax [mV]) and minimum (Bmin [mV]) values of the B signal, and substitute the values
into the following formulas.
Measure the average value of the signal output (Vdt [mV]) with the device ambient temperature of 60°C
and the device in the light-obstructed state, using the horizontal idle transfer level as a reference.
After measuring 6, measure the maximum (Vdmax [mV]) and minimum (Vdmin [mV]) values of the dark
signal output and substitute the values into the following formula.
Set to the standard imaging condition II. Adjusting the luminous intensity so that the value of the Gr signal
output is 150mV, and then insert R, G and B filters and measure the difference between G signal lines
( Glr, Glg, Glb [mV]) as well as the value of the G signal output (Gar, Gag, Gab). Substitute the values
into the following formula.
Lci =
Adjust the Y signal output generated by the strobe light to 150mV. After setting the strobe light so that it
strobes with the following timing, measure the residual signal amount (Vlag). Substitute the value into the
following formula.
Lag = (Vlag/150)
Srg = (Rmax – Rmin)/150
Sbg = (Bmax – Bmin)/150
Vdt = Vdmax – Vdmin [mV]
Gai
Gli
Strobe light timing
100 [%] (i = r, g, b)
Output
100 [%]
VD
100 [%]
100 [%]
100 [%]
Light
Y signal output 150mV
– 19 –
Vlag (lag)
ICX274AQF
Related parts for ICX274
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Ic,video Amplifier,bipolar,can,10pin,metal
Manufacturer:
Freescale Semiconductor, Inc
Datasheet:
Part Number:
Description:
Ic,telephone Dialer,tone/pulse,cmos,dip,24pin,plastic
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Ic For Landing Correction
Manufacturer:
Panasonic Corporation of North America
Datasheet:
Part Number:
Description:
Ic,latch,single,8-bit,bipolar,dip,20pin,plastic
Manufacturer:
ETC-unknow
Datasheet:
Part Number:
Description:
Spi Serial E 2 Prom With Block Lock ? Protection
Manufacturer:
IC MICROSYSTEMS
Datasheet:
Part Number:
Description:
Ic For Headphone Stereos With Volume-limiting Circuit
Manufacturer:
Mitsumi Electronics, Corp.
Datasheet:
Part Number:
Description:
Ic For System Reset With Built-in Watchdog Timer
Manufacturer:
Mitsumi Electronics, Corp.
Datasheet:
Part Number:
Description:
Ic For System Reset With Built-in Watchdog Timer
Manufacturer:
Mitsumi Electronics, Corp.
Datasheet:
Part Number:
Description:
Ic ? 100 Ma Pnp Silicon Af Transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Ic > Analog Ic > Communication Ic
Manufacturer:
AUK Co., Ltd.
Datasheet:
Part Number:
Description:
ic reg ldo 3.3v .15a sot23-5... ic reg ldo 150ma 3.3v sot23-5...
Manufacturer:
Micrel
Datasheet:
Part Number:
Description:
ic reg ldo 500ma 1% 3.3v sot23-5... ic reg ldo 3.3v .5a sot23-5...
Manufacturer:
Micrel
Datasheet:
Part Number:
Description:
Ic,prom,256x8,ttl,dip,20pin,plastic
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Ic Fm/am Radio Cxa1111an
Manufacturer:
Sony Electronics
Datasheet:
Part Number:
Description:
Ic,rf Modulator,bipolar,sop,16pin,plastic
Manufacturer:
Sanyo Semiconductor Corporation
Datasheet: