ISO1H816GAUMA1 Infineon, ISO1H816GAUMA1 Datasheet
ISO1H816GAUMA1
Related parts for ISO1H816GAUMA1
ISO1H816GAUMA1 Summary of contents
Page 1
...
Page 2
... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...
Page 3
Coreless Transformer Isolated Digital Output 8 Channel 1.2A High-Side Switch Product Highlights • Coreless transformer isolated data interface • Galvanic isolation • 8 High-side output switches 1.2A • µC compatible 8-bit serial peripheral • Isolated return path for DIAG signal ...
Page 4
Pin Configuration and Functionality 1.1 Pin Configuration Pin Symbol Function 1 N.C. Not connected 2 VCC Positive 3.3/5V logic supply 3 DIS Output disable 4 CS Chip select 5 SCLK Serial Clock 6 SI Serial Data input 7 N.C. ...
Page 5
Pin Functionality VCC (Positive 3.3/5V logic supply) The VCC supplies the input interface that is galvanically isolated from the output driver stage. The input interface can be supplied with 5V. DIS (Output disable) The high-side outputs OUT0...OUT7 immediately switched ...
Page 6
Blockdiagram Figure 2 Blockdiagram Datasheet Isolation Galvanic 6 TM ISOFACE ISO1H816G Blockdiagram Version 2.0, 2009-07-28 ...
Page 7
Functional Description 3.1 Introduction The ISOface ISO1H816G includes 8 high-side power switches that are controlled by means of the integrated µC compatible SPI interface. OUT0...OUT7 are controlled by the data of the serial input SI. The IC can replace ...
Page 8
Power Transistor Overcurrent Protection The outputs are provided with a current limitation that enters a repetitive switched mode after an initial peak current has been exceeded. The initial peak short circuit current limit is set to I L(SCp) the ...
Page 9
Serial Interface The ISO1H816G contains a serial interface that can be directly controlled by the microcontroller output ports. 3.5.1 SPI Signal Description CS - Chip select. The system microcontroller selects the ISO1H816G by means of the CS pin. Whenever ...
Page 10
ICs is needed. All ICs share the same clock and chip select port of the SPI master. That is all ICs are active and addressed simultaneously. The data out of the µC is connected to the SI of the ...
Page 11
Serial Interface Timing CS SCLK n+7 n n-1 Figure 11 Serial interface t CS CSS SCLK MSB In Figure 12 Serial input timing diagram CS SCLK SO MSB Out Figure 13 Serial output ...
Page 12
Electrical Characteristics Note: All voltages at pins 2to 14 are measured with respect to ground GNDCC (pin 15). All voltages at pin 20 to pin 36 and TAB are measured with respect to ground GNDbb (pin 19). The voltage ...
Page 13
Thermal Characteristics Parameter -25 ... 125°C, V =15...30V unless otherwise specified Thermal resistance junction - case Thermal resistance @ min. footprint Thermal resistance @ 6cm² cooling area 1) Device on 50mm*50mm*1.5mm epoxy PCB ...
Page 14
Voltage domain V Operating voltage bb (Output interface) Undervoltage shutdown Undervoltage restart Undervoltage hysteresis Undervoltage current Operating current Leakage output current (included low, each channel Dx Voltage domain V Operating voltage CC (Input interface) Undervoltage shutdown ...
Page 15
Output Protection Functions 1) Parameter -25 ... 125°C, V =15...30V unless otherwise specified Initial peak short circuit current limit, each channel T = -25° 30V 700µ ...
Page 16
Input Interface Parameter -25 ... 125°C, V =15...30V unless otherwise specified Input low state voltage (SI, DIS, CS, SCLK) Input high state voltage (SI, DIS, CS, SCLK) Input voltage hysteresis (SI, DIS, CS, ...
Page 17
SPI Timing Parameter -25 ... 125°C, V =15...30V unless otherwise specified Serial clock frequency Serial clock period (1/fclk) CS Setup time (falling edge falling edge of SCLK) CS Hold time ...
Page 18
... Short term temporary overvoltage Minimum external air gap (clearance) Minimum external tracking (creepage) Minimum Internal Gap 1) not subject to production test, verified by characterization; Production Test with 1100V, 100ms duration 4.11 Reliability For Qualification Report please contact your local Infineon Technologies office! Datasheet Value 500 ISO 1250 2.6 2 ...
Page 19
Datasheet Electrical Characteristics 19 TM ISOFACE ISO1H816G Version 2.0, 2009-07-28 ...
Page 20
Datasheet Electrical Characteristics 20 TM ISOFACE ISO1H816G Version 2.0, 2009-07-28 ...
Page 21
Package Outlines PG-DSO-36 (Plastic Dual Small Outline Package) Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side Figure 14 PG-DSO-36 Datasheet 1.1 ±0.1 15.74 ±0.1 (Heatslug) 0.65 36x +0.13 0.25 0. ...
Page 22
... Geben Sie uns die Chance, hohe Leistung durch umfassende Qualität zu beweisen. Wir werden Sie überzeugen Published by Infineon Technologies AG Quality takes on an all encompassing significance at Semiconductor Group. bestmöglichen For us it means living up to each and every one of your demands in the best possible way ...