LCMXO256E-4MN100C Lattice, LCMXO256E-4MN100C Datasheet - Page 19

no-image

LCMXO256E-4MN100C

Manufacturer Part Number
LCMXO256E-4MN100C
Description
CPLD - Complex Programmable Logic Devices 256 LUTs 78 IO 1.2V -4 Spd
Manufacturer
Lattice
Datasheet

Specifications of LCMXO256E-4MN100C

Rohs
yes
Memory Type
SRAM
Number Of Macrocells
128
Maximum Operating Frequency
550 MHz
Delay Time
4.2 ns
Number Of Programmable I/os
78
Operating Supply Voltage
1.2 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
0 C
Package / Case
CSBGA-100
Mounting Style
SMD/SMT
Factory Pack Quantity
1800
Supply Current
10 mA
Supply Voltage - Max
1.26 V
Supply Voltage - Min
1.14 V

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LCMXO256E-4MN100C
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
Lattice Semiconductor
2. Left and Right sysIO Buffer Pairs
Typical I/O Behavior During Power-up
The internal power-on-reset (POR) signal is deactivated when V
After the POR signal is deactivated, the FPGA core logic becomes active. It is the user’s responsibility to ensure
that all V
Banks that are critical to the application. The default configuration of the I/O pins in a blank device is tri-state with a
weak pull-up to VCCIO. The I/O pins will maintain the blank configuration until VCC, VCCAUX and VCCIO have
reached satisfactory levels at which time the I/Os will take on the user-configured settings.
The V
fers. In order to simplify system design while providing consistent and predictable I/O behavior, the I/O buffers
should be powered up along with the FPGA core fabric. Therefore, V
together with the V
Supported Standards
The MachXO sysIO buffer supports both single-ended and differential standards. Single-ended standards can be
further subdivided into LVCMOS and LVTTL. The buffer supports the LVTTL, LVCMOS 1.2, 1.5, 1.8, 2.5, and 3.3V
standards. In the LVCMOS and LVTTL modes, the buffer has individually configurable options for drive strength,
bus maintenance (weak pull-up, weak pull-down, bus-keeper latch or none) and open drain. BLVDS and LVPECL
output emulation is supported on all devices. The MachXO1200 and MachXO2280 support on-chip LVDS output
buffers on approximately 50% of the I/Os on the left and right Banks. Differential receivers for LVDS, BLVDS and
LVPECL are supported on all Banks of MachXO1200 and MachXO2280 devices. PCI support is provided in the top
Banks of the MachXO1200 and MachXO2280 devices. Table 2-8 summarizes the I/O characteristics of the devices
in the MachXO family.
Tables 2-9 and 2-10 show the I/O standards (together with their supply and reference voltages) supported by the
MachXO devices. For further information on utilizing the sysIO buffer to support a variety of standards please see
the details of additional technical documentation at the end of this data sheet.
of the devices also support differential input buffers. PCI clamps are available on the top Bank I/O buffers. The
PCI clamp is enabled after V
figured.
The two pads in the pair are described as “true” and “comp”, where the true pad is associated with the positive
side of the differential input buffer and the comp (complementary) pad is associated with the negative side of
the differential input buffer.
The sysIO buffer pairs in the left and right Banks of the device consist of two single-ended output drivers and
two sets of single-ended input buffers (supporting ratioed and absolute input levels). The devices also have a
differential driver per output pair. The referenced input buffer can also be configured as a differential input buf-
fer. In these Banks the two pads in the pair are described as “true” and “comp”, where the true pad is associ-
ated with the positive side of the differential I/O, and the comp (complementary) pad is associated with the
negative side of the differential I/O.
CC
CCIO
and V
Banks are active with valid input logic levels to properly control the output logic states of all the I/O
CCAUX
CC
supply the power to the FPGA core fabric, whereas the V
and V
CCAUX
CC
supplies
, V
CCAUX
, and V
CCIO
2-16
are at valid operating levels and the device has been con-
CC
and V
CCIO
supplies should be powered up before or
CCAUX
MachXO Family Data Sheet
CCIO
have reached satisfactory levels.
supplies power to the I/O buf-
Architecture

Related parts for LCMXO256E-4MN100C