SIT8103AI-42-33E-100.00000T

Manufacturer Part NumberSIT8103AI-42-33E-100.00000T
DescriptionProgrammable Oscillators 100MHz +/-25ppm 3.3Volt -40C + 85C
ManufacturerSiTime
SIT8103AI-42-33E-100.00000T datasheet
 

Specifications of SIT8103AI-42-33E-100.00000T

RohsyesPackage / Case7 mm x 5 mm
Frequency100 MHzFrequency Stability+/- 25 PPM
Supply Voltage3.3 VLoad Capacitance15 pF
Termination StyleSMD/SMTOutput FormatLVCMOS, LVTTL
Minimum Operating Temperature- 40 CMaximum Operating Temperature+ 85 C
Dimensions5 mm W x 7 mm L x 0.9 mm HProductXO
1
Page 1
2
Page 2
3
Page 3
4
Page 4
Page 1/4

Download datasheet (163Kb)Embed
Next
SiT8103
High Performance 1-110 MHz Oscillator
Features, Benefits and Applications
■ MEMS oscillator with LVCMOS/LVTTL compatible output
■ 1-110 MHz frequency range
■ Frequency stability as low as ±20 PPM
■ Typical current consumption of 6.1 mA in active mode
■ Standby or output enable modes
■ 1.8V, 2.5V - 3.3V supply voltage
TM
■ SoftEdge
configurable rise/fall time for driving higher loads or EMI reduction.
■ Four industry-standard packages: 2.5 x 2.0, 3.2 x 2.5, 5.0 x 3.2, 7.0 x 5.0 mm
■ All-silicon device with outstanding reliability of 2 FIT, 10x improvement over quartz-based devices
■ Ultra short lead time
■ Ideal for consumer electronics: video, set top boxes, HDTV, DVR, scanners, printers, IP camera, etc.
■ Ideal for high-speed serial protocols: Ethernet, USB, SATA, SAS, Fibre Channel, Firewire, PCI Express
Specifications
Electrical Characteristics
[1]
Parameter
Symbol
Output Frequency Range
f
Frequency Stability
F_stab
Aging
Ag
Operating Temperature Range
T_use
Supply Voltage
Vdd
Current Consumption
Idd
Standby Current
I_std
Duty Cycle
DC
Rise/Fall Time
Tr, Tf
Output Voltage High
VOH
Output Voltage Low
VOL
Input Voltage High
VIH
Input Voltage Low
VIL
Startup Time
T_start
Resume Time
T_resume
RMS Period Jitter
T_jitt
RMS Phase Jitter (random)
T_phj
Note:
1. All electrical specifications in the above table are measured with 15pF output load, unless stated otherwise in the Condition. For more information about SoftEdge
rise/fall time for driving higher output load or reducing EMI, download http://www.sitime.com/support2/documents/AN10022-rise-and-fall-time-rev1.1.pdf.
SiTime Corporation
990 Almanor Avenue
Rev. 1.46
Min.
Typ.
Max.
Unit
1
110
MHz
-20
+20
PPM
Inclusive of: Initial stability, operating temperature, rated power,
supply voltage change, load change, shock and vibration.
-25
+25
PPM
-30
+30
PPM
± 20 PPM available in extended commercial
temperature only
-50
+50
PPM
-1.0
1.0
PPM
1st year at 25°C
-20
+70
°C
Extended Commercial
-40
+85
°C
Industrial
1.71
1.8
1.89
V
Any voltage between 2.5V and 3.3V is supported with 1 decimal
point resolution.
2.25
2.5
2.75
V
2.52
2.8
3.08
V
2.97
3.3
3.63
V
6.7
7.5
mA
No load condition, f = 20 MHz, Vdd = 2.5 V, 2.8 V or 3.3 V
6.1
6.7
mA
No load condition, f = 20 MHz, Vdd = 1.8 V
2.4
4.3
μA
ST = GND, Vdd = 3.3 V, Output is Weakly Pulled Down
1.2
2.2
μA
ST = GND, Vdd = 2.5 or 2.8 V, Output is Weakly Pulled Down
μA
0.4
0.8
ST = GND, Vdd = 1.8 V, Output is Weakly Pulled Down
45
50
55
%
All Vdds. f <= 75 MHz
40
50
60
%
All Vdds. f > 75 MHz
1
2
ns
15pF load, 20% - 80% Vdd=2.5V, 2.8V or 3.3V
1.3
2.5
ns
15pF load, 20% - 80% Vdd=1.8V
1.9
2.6
ns
30pF load, 20% - 80% Vdd=2.5V, 2.8V or 3.3V
2.3
3.3
ns
30pF load, 20% - 80% Vdd=1.8V
2.9
3.9
ns
45pF load, 20% - 80% Vdd=2.5V, 2.8V or 3.3V
3.4
4.6
ns
45pF load, 20% - 80% Vdd=1.8V
90%
Vdd
IOH = -4 mA (Vdd = 3.3 V)
IOH = -3 mA (Vdd = 2.8 V and Vdd = 2.5 V)
10%
Vdd
IOH = -2 mA (Vdd = 1.8 V)
70%
Vdd
Pin 1, OE or ST
30%
Vdd
Pin 1, OE or ST
10
ms
Measured from the time Vdd reaches its rated minimum value
3.0
4
ms
Measured from the time ST pin crosses 50% threshold
4.0
ps
f = 75 MHz, Vdd = 2.5 V, 2.8 V or 3.3 V
6.5
ps
f = 75 MHz, Vdd = 1.8 V
0.6
ps
f = 75 MHz @ BW: 900 kHz to 7.5 MHz, VDD = 2.5 V to 3.3 V
0.8
ps
f = 75 MHz @ BW: 900 kHz to 7.5 MHz, VDD = 1.8 V
Sunnyvale, CA 94085
Condition
TM
(408) 328-4400
www.sitime.com
Revised August 11, 2011

SIT8103AI-42-33E-100.00000T Summary of contents

  • Page 1

    ... Note: 1. All electrical specifications in the above table are measured with 15pF output load, unless stated otherwise in the Condition. For more information about SoftEdge rise/fall time for driving higher output load or reducing EMI, download http://www.sitime.com/support2/documents/AN10022-rise-and-fall-time-rev1.1.pdf. SiTime Corporation 990 Almanor Avenue Rev ...

  • Page 2

    ... Pin 4 Voltage 50% Vdd CLK Output T_resume: Time to resume from ST Page Pin Map Connection OE/ST GND CLK VDD Max. Unit 150 ° 6000 V 75 °C/W 24 °C/W 260 ° – years Condition/Test Method Vdd ST Voltage T_resume CLK Output (ST Mode Only) www.sitime.com ...

  • Page 3

    ... Top marking: Y denotes manufacturing origin and XXXX denotes manufacturing lot number. The value of “Y” will depend on the assembly location of the device 4. A capacitor of value 0.1 μ F between Vdd and GND is recommended. 5. The 7050 package with part number designation "-8" has NO center pad. Rev. 1.46 [] Recommended Land Pattern (Unit: mm 0.9 2. 1.15 #4 [5] No Connect #1 1.4 Page [5] 1.9 1.1 2.2 1.4 2.54 1.5 5.08 2.2 www.sitime.com ...

  • Page 4

    ... SiTime Corporation 2011. The information contained herein is subject to change at any time without notice. SiTime assumes no responsibility or liability for any loss, damage or defect of a Product which is caused in whole or in part by (i) use of any circuitry other than circuitry embodied in a SiTime product, (ii) misuse or abuse including static discharge, neglect or accident, (iii) unauthorized modification or repairs which have been soldered or altered during assembly and are not capable of being tested by SiTime under its normal test conditions, or (iv) improper installation, storage, handling, warehousing or transportation, or (v) being subjected to unusual physical, thermal, or electrical stress ...