MAX13046EELT+T Maxim Integrated Products, MAX13046EELT+T Datasheet - Page 9

• Manufacturer Part Number: MAX13046EELT+T
• Description: IC LEVEL TRANS LL 6-UDFN
• Manufacturer: Maxim Integrated Products

Specifications of MAX13046EELT+T

• Logic Function: Translator, Bidirectional
• Number Of Bits: 1
• Input Type: Logic
• Output Type: Logic
• Data Rate: 16Mbps
• Number Of Channels: 1
• Number Of Outputs/channel: 1
• Differential - Input:output: No/No
• Propagation Delay (max): 15ns
• Voltage - Supply: 1.65 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 6-µDFN
• Supply Voltage: 1.65 V ~ 5.5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: MAX13046EELT+T; MAX13046EELT+TTR

For proper operation, ensure that +1.65V ≤ V
+5.5V and +1.1V ≤ V
(V
+ 0.3V) does not damage the device. The speed of the
rise time accelerator circuitry limits the maximum data
rate for the MAX13046E/MAX13047E to 16Mbps.
The MAX13046E/MAX13047E have an internal rise-time
accelerator, allowing operation up to 16Mbps. The rise-
time accelerators are present on both sides of the
device and act to speed up the rise time of the input
and output of the device, regardless of the direction of
the data. The triggering mechanism for these accelera-
tors is both level and edge sensitive. To guarantee
operation of the rise time accelerators the maximum
parasitic capacitance should be less than 200pF on the
I/O lines.
Drive SHDN low to place the MAX13046E/MAX13047E
in shutdown mode and drive SHDN high for normal
operation. Activating the shutdown mode disconnects
the internal 10kΩ pullup resistors on the I/O V
V
L
CC
lines. This forces the I/O lines to a high-impedance
+ 0.3V). During power-up sequencing, V
I/O V
L
_______________________________________________________________________________________
L
V
≤ the minimum of either +3.6V or
L
10kΩ
Rise-Time Accelerators
PU1
Level Translation
Shutdown Mode
ACCELERATOR
ONE-SHOT
RISE-TIME
Single- and Dual-Bidirectional
CC
L
SHDN
and I/O
≥ (V
CC
CC
≤
GATE BIAS
N
state, and decreases the supply current to less than
1µA. The high-impedance I/O lines in shutdown mode
allow for use in a multidrop network. The MAX13046E/
MAX13047E have a diode from each I/O to the corre-
sponding supply rail and GND. Therefore, when in shut-
down mode, do not allow the voltage at I/O V
(V
0.3V).
Certain applications require sections of circuitry to be
disconnected to save power. When V
V
enters shutdown mode. In this mode, I/O V
driven without damage to the device; however, data
does not translate from I/O V
more than V
the pullup resistors at I/O V
lowest possible supply current from V
connected, it is recommended that the voltage at the
V
When V
device enters shutdown mode. In this mode, I/O V
can still be driven without damage to the device; howev-
er, data does not translate from I/O V
CC
CC
L
Operation with One Supply Disconnected
+ 0.3V), or the voltage at I/O V
Low-Level Translator
is disconnected or connected to ground, the device
supply input be approximately equal to GND.
GND
CC
ACCELERATOR
ONE-SHOT
RISE-TIME
is connected and V
TH_L_VCC
below V
Functional Diagram
L
PU2
10kΩ
and I/O V
L
L
L
, the device disconnects
V
to I/O V
CC
is less than V
CC
CC
L
L
CC
to exceed (V
is connected and
when V
I/O V
to I/O V
CC
. To achieve the
CC
L
. If V
L
can still be
TH_VL
to exceed
CC
L
CC
.
is dis-
CC
, the
falls
CC
9
+