uEZGUI-EXP1 FDI, uEZGUI-EXP1 Datasheet

no-image

uEZGUI-EXP1

Manufacturer Part Number
uEZGUI-EXP1
Description
Daughter Cards & OEM Boards UEZ GUI EXPANSION BOARD
Manufacturer
FDI
Datasheet

Specifications of uEZGUI-EXP1

Product Category
Daughter Cards & OEM Boards
Rohs
yes
Product
Interface Expansion Board
Description/function
The uEZGUI Expansion Board enhances the capabilities of the standard uEZGUI board to include additional IO capabilities
Interface Type
Ethernet, RS-232, RS-485, USB
Operating Supply Voltage
7 V to 24 V
For Use With
uEZGUI Board
 
 
 
 
Copyright ©2010, Future Designs, Inc., All Rights Reserved
uEZGUI-EXP1
User’s Manual
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Related parts for uEZGUI-EXP1

uEZGUI-EXP1 Summary of contents

Page 1

... User’s Manual         Copyright ©2010, Future Designs, Inc., All Rights Reserved                             ...

Page 2

... USB Host – P2 ________________________________________________________________  9  Ethernet – J2 ________________________________________________________________  10  Connecting to the uEZGUI Boards  _______________________________________________  10    Information in this document is provided solely to enable the use of Future Designs products. FDI assumes no liability whatsoever, including  ...

Page 3

... Expansion Connector  The uEZGUI‐2478‐43WQS includes a 50 pin FPC Expansion Connector that provides a wide variety of  capabilities for user expansion, ranging from 10/100 Ethernet to USB Host, etc. The table below provides  ...

Page 4

Pin #  Pin Name 1  Ground (GND)        2  P0.11_RXD2_SCL2_MAT3                    3  P0.10_TXD2_SDA2_MAT3  SDA2 ‐ I2C2 data input/output (this is not an open‐drain pin).                    4  P0.20_DTR1_SCL1              5  P0.19_DSR1_SDA1              6  P0.22_RTS1  ...

Page 5

P0.9_I2STX_SDA_MOSI1_ MAT2.3                                        P0.8_I2STX_WS_MISO1_ MAT 2.2     17                       P0.7_I2STX_CLK_SCK1_M AT 2.1     18                 P0.6_I2SRX_SDA_SSEL1_ ...

Page 6

External reset input: A LOW on this pin resets the device, causing I/O  23  RESET_IN  ports and peripherals to take on their default states, and processor  execution to begin at address 0. TTL with hysteresis, 5 V tolerant  24  RESET_OUT  RSTOUT ‐ This is a 3.3 V pin. LOW on this pin indicates LPC2478 being  in Reset state        P0[26] General purpose digital input/output pin. 25  P0.26_AD03_AOUT_RXD3  AD0[3] ‐ A/D converter 0, input 3.       AOUT ‐ D/A converter output.       RXD3 ‐ Receiver input for UART3       P1[31] – General purpose digital input/output pin. 26  P1.31_SCK1_AD0.5  SCK1 ‐ Serial Clock for SSP1. AD0[5] ‐ A/D converter 0, input 5       27  ...

Page 7

P0[31] ‐ General purpose digital input/output pin. 43  USBD_DP  USB_D+2 ‐ USB port 2 bidirectional D+ line 44  USBD_DM  USB_D‐2 ‐ USB port 2 bidirectional D ‐line       P1[30] ‐ General purpose digital input/output pin.       USB_PWRD2 ‐ Power Status for USB port 2. 45  USBD_VBUS  VBUS ‐ Monitors the presence of USB bus power. Note: This signal  must be HIGH for USB reset to occur. I ‐ AD0[4] ‐ A/D converter 0,  input 4  46  5volts (5VO)  5.0 Volts DC 47  5volts (5VO)  5.0 Volts DC 48  5volts (5VO)  5.0 Volts DC 49  3p3 volts (3V3)  3.3 Volts DC ...

Page 8

... Serial Port – P3    The uEZGUI‐EXP1 Board includes one female DB9 Serial Port Connector.  This connector may operate in  either RS232 or RS485 (Full‐duplex) interface levels depending on jumper settings of JP1 through JP4.  ...

Page 9

... USB Host – P2    The uEZGUI‐EXP1 Board includes one USB Host Port allowing the unit to interface to various USB  peripherals such as a USB Flash Drive (Thumb Drive). The operational mode of this port is dependent on  ...

Page 10

... Pin Number  1  2  3  4  5  6  7    8  uEZGUI‐2478‐43WQS with uEZGUI‐EXP1       Description  Tx+  Tx‐  Rx+  75 ohm terminated  75 ohm terminated  Rx‐  75 ohm terminated  75 ohm terminated  ...

Page 11

... uEZGUI‐2478‐70WVE with uEZGUI‐EXP1  uEZGUI‐2478‐43WQS with uEZGUI‐EXP1 mounted in OEM Housing            ...

Related keywords