MAX1276EVKIT Maxim Integrated, MAX1276EVKIT Datasheet - Page 2

• Manufacturer Part Number: MAX1276EVKIT
• Description: Data Conversion IC Development Tools Evaluation Kit/Evaluation System for the MAX1070/71/72/75#79/MAX1224/25/MAX1274#79
• Manufacturer: Maxim Integrated
• Series: MAX1276, MAX1278r

Specifications of MAX1276EVKIT

• Interface Type: QSPI, Serial (SPI, Microwire)

The MAX1276EVKIT provides a proven PC-board layout
facilitating evaluation of the MAX1276. It must be con-
nected to appropriate power supplies and timing sig-
nals for proper operation. For standard evaluations, DC
supplies are required for the AVDD, VLOGIC, +7V, and
-3V power inputs. Depending on the intended applica-
tion and option settings, AVDD and VLOGIC supplies
can be shared and the +7V and -3V supplies are only
required if the on-board buffer circuitry is to be utilized.
Additional supplies and references may be needed to
accommodate optional input configurations. Connector
P1 provides a convenient connection for a logic analyz-
er or other user system. Refer to the data sheet of the
part being evaluated for timing requirements.
The MAX1276EVC16 EV system connects to an IBM-
compatible PC running Windows 98/ME/XP. The evalu-
ation system connects to the PC’s serial communica-
tions port. See the Quick Start Using the MAX1276 EV
System section for setup and operating instructions.
MAX1276 Evaluation Kit/Evaluation System
Note: Indicate that you are using the MAX1276 when contacting these component suppliers.
SPI is a trademark of Motorola, Inc.
2
Taiyo Yuden
TDK
DESIGNATION QTY
_______________________________________________________________________________________
U2, U3
ACIN
FB1
FB2
U1
U4
—
—
—
SUPPLIER
MAX1276 Stand-Alone EV Kit
Component List (continued)
1
1
2
1
1
1
7
1
1
SMA connector
MAX1276ETC (12-pin TQFN)
MAX4430ESA (8-pin SO)
Texas Instruments
SN74LVC1G08DBVR
Ferrite bead (0805)
Murata BLM21A102S
0Ω resistor (0805)
Shunts
CD-ROM with MAX1276 EV kit
software
MAX1276 EV kit PC board
MAX1276 EV System
DESCRIPTION
800-348-2496
847-803-6100
PHONE
847-925-0899
847-390-4405
To use the MAX1276EVKIT with a logic analyzer, the
following equipment is needed:
• Power supplies for the MAX1276EVKIT
• Logic analyzer and digital waveform generator or µC
• Deserializer board (optional). A deserializer board
Follow the steps below to verify board operation. Do
not turn on the power supply until all connections
are completed.
1) Set jumpers JU1–JU6 according to
FAX
1) VDD DC supply (5.0V for the MAX1276)
2) VLOGIC DC supply (1.8V to VDD)
3) +7.0V positive supply buffer
4) -3.0V negative supply buffer
5) AC input (4.096V
6) DC supplies for common-mode voltages (2.048V
system with SPI™ capabilities
can be fitted to the EV kit for use with a parallel
logic-analyzer interface. Be sure the selected cir-
cuitry supports the intended operating speed of the
device under test (DUT). See the Deserializer Board
(Optional) section for a proven design example.
MAX1276, or use Tables 3, 4, and 5 to select the
jumper configuration for other devices. It is highly
recommended that the shunts for JU1 and JU2 be
removed until the DUT and buffers are fully powered
and input levels have been verified to avoid possible
damage to the test device if pins are taken above
the VDD supply or below ground. See the Input-
Signal Setup Procedure section for a description of
the possible input options.
for the MAX1276)
Quick Start Using a Logic
www.t-yuden.com
www.component.tdk.com
Component Suppliers
P-P
for the MAX1276)
Required Equipment
WEBSITE
Table
Analyzer
Procedure
1 for the