UMFT220XA-01 FTDI, UMFT220XA-01 Datasheet

no-image

UMFT220XA-01

Manufacturer Part Number
UMFT220XA-01
Description
Interface Development Tools USB to SPI/FT1248 Dev Mod for FT220X
Manufacturer
FTDI
Type
USB to SPIr
Datasheet

Specifications of UMFT220XA-01

Rohs
yes
Product
Development Modules
Tool Is For Evaluation Of
FT220XQ
Interface Type
SPI
Operating Supply Voltage
3.3 V
Dimensions
30.1 mm x 12.2 mm x 2.2 mm
Tradename
X-Chip
1
Devices International
SPI/FT1248 Development
UMFT220XA USB to 4-bit
Future Technology
Introduction
The UMFT220XA is a development module
for FTDI‟s FT220XQ, one of the devices
from FTDI‟s range of USB interface bridging
integrated circuit devices. FT220X is a USB
to 4-bit SPI/FT1248 (only up to 4 bit wide)
interface with a battery charger detection
feature, which can allow batteries to be
charged with a higher current from a
dedicated charger port (without the
FT220X being enumerated). In addition,
asynchronous and synchronous bit bang
interface modes are available. The
internally generated clock (6MHz, 12MHz
and 24MHz) can be brought out on the
CBUS pin to be used to drive a
microprocessor or external logic.
The UMFT220XA is a module which is
designed to plug into a standard 0.3” wide
16 pin DIP socket. All components used,
including the FT220XQ are Pb-free (RoHS
compliant).
UMFT220XA is a USB to 4-bit SPI/FT1248 DIP module with a 0.3” row pitch.
Use of FTDI devices in life support and/or safety applications is entirely at the user‟s risk, and the user agrees
to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting
Datasheet
Module
Ltd
from such use.
1.1
The UMFT220XA is fitted with a FT220XQ; all
the features of the FT220X can be utilized with
the UMFT220XA. For a full list of the FT220X‟s
features please see the FT220X datasheet which
can be found by clicking here.
In addition to the features listed in the FT220X
datasheet, the UMFT220XA has the following
features:
Features
Small PCB assembly module designed to fit a
to be connected to a PC via a standard A to
mini-B USB cable.
standard 7.62mm (0.3”) wide 16 pin DIP
socket. Pins are on a 2.54mm (0.1”) pitch.
Functionally configurable using solder links.
The default solder links setup enables the
module to function without peripheral wires
or application board.
enable external power supply options and
variation of logic reference levels.
On board USB „mini-B‟ socket allows module
Document Reference No.: FT_000517
Other configurations
Clearance No.: FTDI#
UMFT220XA
Version 1.1
267

Related parts for UMFT220XA-01

UMFT220XA-01 Summary of contents

Page 1

... Devices International Ltd Datasheet UMFT220XA USB to 4-bit SPI/FT1248 Development Module UMFT220XA is a USB to 4-bit SPI/FT1248 DIP module with a 0.3” row pitch. Introduction 1 The UMFT220XA is a development module for FTDI‟s FT220XQ, one of the devices from FTDI‟s range of USB interface bridging integrated circuit devices ...

Page 2

... Table of Contents 1 Introduction ................................................................................... 1 1.1 Features ........................................................................................................ 1 2 Driver Support ................................................................................ 3 3 Ordering Information ..................................................................... 3 4 UMFT220XA Signals and Configurations ......................................... 4 4.1 UMFT220XA Pin Out ...................................................................................... 4 4.2 Signal Descriptions ....................................................................................... 5 4.3 CBUS Signal Options ..................................................................................... 6 5 Module Configurations .................................................................... 7 5.1 Solder Link Configuration Options ................................................................. 7 5.2 Solder Link Modfications ............................................................................... 7 5.3 BUS Powered Configuration .......................................................................... 8 5.4 Self Powered Configuration ........................................................................... 9 5.5 USB Bus Powered with Power Switching Configuration .............................. 10 5 ...

Page 3

... The drivers listed above are all available to download for free from www.ftdichip.com. Various 3rd Party Drivers are also available for various other operating systems - visit Ordering Information & TID 3 Module Code Utilised IC Code UMFT201XA-01 FT201XQ UMFT220XA-01 FT220XQ UMFT220XA-02 FT220XQ UMFT221XA-01 FT221XQ UMFT230XA-01 FT230XQ UMFT231XA-01 ...

Page 4

... UMFT220XA Signals and Configurations 4 UMFT220XA Pin Out 4.1 Figure 4.1 – Module Pin Out Figure 4.1 illustrates the signals available on the DIL pins. The LHS shows the pinout when the module is viewed from the bottom. The RHS shows what signals are available (on the pins below) when viewed from the top ...

Page 5

... FT1248 Chip select input to enable the device interface. Active low logic. J2-7 SCLK Input FT1248 Clock input from FT1248 interface master. Table 4.1 – Module Pin Out Description Document Reference No.: FT_000517 Copyright © 2012 Future Technology Devices International Limited UMFT220XA Version 1.1 267 Clearance No.: FTDI# 5 ...

Page 6

... P-Channel logic level MOSFET switch. NOTE: This function is driven by an open-drain to ground with no internal pull-up, this is specially designed to aid battery charging applications. UMFT220XA connects an on-board 47K pull-up to all CBUS and DBUS pins. Transmit data LED drive – open drain pulses low when transmitting data via USB. Receive data LED drive – ...

Page 7

... Solder Link Modfications 5.2 The UMFT220XA has two solder links fixed to the top side of the PCB. These solder link can be adjusted by removing the solder linking the two PADs to produce an open or by placing a solder blob to produce a short. By default the UMFT220XA has both solder links shorting their pads. To allow for enhanced flexibility of this module remove both solder links and wire the header pins according to the power setup required ...

Page 8

... TTL Mode Solder Link JP1 - Closed Figure 5.1 – Bus Powered Configuration A bus powered configuration draws its power from the USB host/hub. The UMFT220XA is configured by default bus powered mode. Figure 5.1 illustrates the UMFT220XA module in a typical USB bus powered design configuration. By default solder bridge connections link VCCIO to 3V3OUT, and VCC to VBUS ...

Page 9

... Driving a level to the RESET# pin of the UMFT220XA will override the effect of this voltage divider. When the FT220X is in reset the USB DP signal pull-up resistor connected to the data lines is disconnected and no current can flow down the USB lines. An example of interfacing the FT220X with a Microcontroller‟ ...

Page 10

... Document Reference No.: FT_000517 VCCIO 3V3OUT GND Self-Sorced 3.3V TTL Mode Solder Link JP1 - Closed Viewing Pin thourgh the board from the top. Copyright © 2012 Future Technology Devices International Limited UMFT220XA Version 1.1 Clearance No.: FTDI# P-Channel Power MOSFET s d 0.1uF 10K g Soft ...

Page 11

... SCLK Optional IO2 SS# Optional IO3 MISO GND Solder Link JP1 - Open Viewing Pin thourgh the board Copyright © 2012 Future Technology Devices International Limited UMFT220XA Version 1.1 Clearance No.: FTDI# SCLK SS# MISO VCCIO VCC 3V3OUT VBUS Solder Link JP2 - Closed from the top. ...

Page 12

... Optional IO2 SS# Optional IO3 MISO VCCIO 3V3OUT GND Solder Links JP1 - Closed Viewing Pin thourgh the board Copyright © 2012 Future Technology Devices International Limited UMFT220XA Version 1.1 Clearance No.: FTDI# Vcc = 3.3V SCLK SS# MISO VCC VBUS Solder Links JP2 - Open from the top. 12 ...

Page 13

... All dimensions are given in millimetres. The UMFT220XA module exclusively uses lead free components, and is fully compliant with European Union directive 2002/95/EC. Document Reference No.: FT_000517 2.54 30.1 * 5.6mm for the UMFT220XA-01 4.6mm for the UMFT220XA-02 Copyright © 2012 Future Technology Devices International Limited UMFT220XA Version 1.1 267 Clearance No ...

Page 14

... UMFT220XA Module Circuit Schematic 7 Figure 7.1 – Module Circuit Schematic Document Reference No.: FT_000517 Copyright © 2012 Future Technology Devices International Limited UMFT220XA Version 1.1 267 Clearance No.: FTDI# 14 ...

Page 15

... Following a power-on reset or a USB reset the FT220X will scan its internal MTP ROM and read the USB configuration descriptors stored there. The default values programmed into the internal MTP ROM in the FT220XQ used on the UMFT220XA-01 and UMFT220XA-02 are shown in Table 8.1. Parameter ...

Page 16

... Tel: +86 (0)21 6235 1596 Fax: +86 (0)21 6235 1595 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) FTDI Web site for the contact details of our distributor(s) and sales Copyright © 2012 Future Technology Devices International Limited UMFT220XA Version 1.1 267 Clearance No.: FTDI# us.sales@ftdichip.com us.support@ftdichip.com us.admin@ftdichip.com cn.sales@ftdichip.com cn ...

Page 17

... Figure 5.2 – Self-Powered Configuration ...................................................................................................... 9 Figure 5.3 – Bus Powered with Power Switching Configuration .............................................................. 10 Figure 5.4 – USB Bus Powered 3.3V Logic Drive ....................................................................................... 11 Figure 5.5 – USB Self Powered 3.3V Logic Drive ....................................................................................... 12 Figure 6.1 – UMFT220XA Module Dimensions ........................................................................................... 13 Figure 7.1 – Module Circuit Schematic ........................................................................................................ 14 List of Tables Table 4.1 – Module Pin Out Description ........................................................................................................ 5 Table 4.2 – ...

Page 18

... Product Page: Document Feedback: Version 1.0 Initial Datasheet Created Version 1.1 Added links, referances to silicon revision, TID and logos. Copyright © 2012 Future Technology Devices International Limited Document Reference No.: FT_000517 UMFT220XA FT_000517 FTDI# 267 http://www.ftdichip.com/FT-X.htm Send Feedback UMFT220XA Version 1.1 Clearance No.: FTDI# 267 09/02/12 13/06/12 18 ...

Related keywords