LCMXO2-1200ZE-B-EVN Lattice, LCMXO2-1200ZE-B-EVN Datasheet

Page 1

MachXO2 Breakout Board Evaluation Kit  User’s Guide February 2013 Revision: EB68_02.0 ...

Page 2

... MachXO2 Breakout Board – The board is a 3” x 3” form factor that features the following on-board components and circuits: – MachXO2 FPGA – Current board version: LCMXO2-7000HE-4TG144C  (Previous board version no longer available: LCMXO2-1200ZE-1TG144C) – USB mini-B connector for power and programming – ...

Page 3

... Touch a metal USB housing to equalize voltage potential between you and the board. Software Requirements You should install the following software before you begin developing new designs for the Breakout board: ® • Lattice Diamond design software • FTDI Chip USB hardware drivers (installed as an option within the Diamond installation program) MachXO2 Device This board currently features the MachXO2-7000HE FPGA which offers embedded Flash technology for instant- on, non-volatile operation in a single chip ...

Page 4

... Communication with the Breakout Board with a PC via the USB connection cable requires installation of the FTDI chip USB hardware drivers. Loading these drivers enables the computer to recognize and program the Breakout Board. Drivers can be loaded as part of the installation of Lattice Diamond design software or Diamond Program- mer stand-alone package. ...

Page 5

... Continue to Programming a Demo Design with Lattice Diamond Design Software. Programming a Demo Design with the Lattice Diamond Programmer The demonstration design is pre-programmed into the MachXO2 Breakout Board by Lattice. If you have changed the design but now want to restore the Breakout Board to factory settings, use the procedure described below. ...

Page 6

... USB program/power port, an LED array, and header landings with electrical connections to most of the FPGA’s programmable I/O, power, and JTAG pins. The board is powered by the PC’s USB port or optionally with external power. You may create or modify the program files and reprogram the board using Lattice Diamond soft- ware. ...

Page 7

... Table 2. Expansion Connector Reference Reference Designators Part Number Schematic Reference U2: FT2232H USB-to-JTAG interface and dual USB UART/FIFO IC J7:USB_MINI_B Programming and debug interface U3: LCMXO2- 7000-LUT device packaged 20mm, 144-pin TQFP 7000HE-4TG144C D8-D1 Red LEDs J2: header_2x20 J3: header_2x20 User-definable I/O J4: header_2x20 J5: header_2x20 ...

Page 8

Table 3. Expansion Header Pin Information (J2) Header Pin Number PT12D / SDA / PCLKC0_0 PT22D / SDA / PCLKC0_0 20 ...

Page 9

Table 4. Expansion Header Pin Information (J3) Header Pin Number ...

Page 10

Table 5. Expansion Header Pin Information (J4) Header Pin Number ...

Page 11

Table 6. Expansion Header Pin Information (J5) Header Pin Number ...

Page 12

Figure 4. J2/J4 Header Landing Callout IO0 109 110 111 112 GND GND 113 114 115 117 119 120 GND GND 121 122 125 126 127 128 GND GND 130 131 132 133 136 137 GND ...

Page 13

... Table 8. JTAG Interface Reference Item Reference Designators Part Number Manufacturer Web Site D8 D1 LCMXO2-7000HE 4TG144C Item Description U3 LCMXO2-7000HE-4TG144C Lattice Semiconductor www.latticesemi.com Description U1 FT2232HL Future Technology Devices International (FTDI) www.ftdichip.com 13 MachXO2 Breakout Board Evaluation Kit User’s Guide LED Array MachXO2 Pin ...

Page 14

... The USB mini-B socket of the Breakout Board serves as the programming and debug interface. JTAG Programming: For JTAG programming, a preprogrammed USB PHY peripheral controller is provided on the Breakout Board to serve as the programming interface to the MachXO2 FPGA. Programming requires the Lattice Diamond or ispVM System software. Table 11. USB Interface Reference Reference Designators ...

Page 15

Board Modifications This section describes modifications to the board to change or add functionality. Bypassing the USB Programming Interface The USB programming interface circuit bypassed by removing the 0 ohm resistors: R5, R6, R7, R8 (See landing J1 provides JTAG ...

Page 16

... Technical Support Assistance Hotline: 1-800-LATTICE (North America) +1-503-268-8001 (Outside North America) e-mail: techsupport@latticesemi.com Internet: www.latticesemi.com MachXO2 Breakout Board Evaluation Kit User’s Guide section for details on downloading and reprogramming the China RoHS Environment-Friendly Ordering Part Number LCMXO2-7000HE-B-EVN 1 LCMXO2-1200ZE-B-EVN 16 Use Period (EFUP) ...

Page 17

... February 2013 © 2013 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. Version 01 ...

Page 18

Appendix A. Schematics Note: The schematics are drawn using the MachXO2-1200ZE device. Please consult Tables 3 through 6 for -1200 and -7000HE pin name and bank synonyms. Pin numbers are correct for either device. Figure 7. Block Diagram JTAG HEADER ...

Page 19

Figure 8. USB Interface to JTAG VCCIO 56 VCCIO 42 VCCIO 31 VCCIO 20 VCORE 64 VCORE 37 VCORE 12 VPLL 9 VPHY 4 19 MachXO2 Breakout Board Evaluation Kit User’s Guide GND 51 GND 47 ...

Page 20

Figure 9. FPGA MachXO2 Breakout Board Evaluation Kit User’s Guide 20 ...

Page 21

Figure 10. FPGA MachXO2 Breakout Board Evaluation Kit User’s Guide 21 ...

Page 22

Figure 11. Power LEDs GND MachXO2 Breakout Board Evaluation Kit User’s Guide STATUS_LED0 STATUS_LED1 STATUS_LED2 ...

Page 23

... Neltron 5075BMR-05-SM-CR Murata BLM18AG601SN1D Yageo RC0402FR-075K1L Yageo RC0402FR-072K2L Yageo RC0603JR-070RL Yageo RC0402FR-0712KL Yageo RC0402FR-0710KL Yageo RC0603JR-070RL Vishay/Dale CRCW06031R00JNEAHP Yageo RC0603FR-07100RL Yageo RC0402FR-071KL Yageo RC0603FR-07100RL FTDI FT2232HL Microchip 93LC56C-I/SN Lattice LCMXO2-7000HE-4TG144C or LCMXO2-1200ZE-1TG144C Fairchild Semi FAN1112SX On Semi NCP1117ST33T3G TXC 7M-12.000MAAJ-T CTS CB3LV-3C-50M0000 ...