ADP5062CP-EVALZ

Manufacturer Part NumberADP5062CP-EVALZ
DescriptionPower Management IC Development Tools ADP5062 Evaluation board
ManufacturerAnalog Devices
TypeLinear Regulators - Standard
SeriesADP5062
ADP5062CP-EVALZ datasheet
 


Specifications of ADP5062CP-EVALZ

RohsyesProductEvaluation Boards
Tool Is For Evaluation OfADP5062Input Voltage4 V to 6.7 V
Description/functionBattery charger (isolated flyback)Interface TypeI2C
Maximum Operating Temperature+ 125 CMinimum Operating Temperature- 40 C
Output Current2.1 AFactory Pack Quantity1
For Use WithADP5062  
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Page 1/44

Download datasheet (812Kb)Embed
Next
Data Sheet
FEATURES
4 mm × 4 mm LFCSP package
Fully programmable via I
2
C
Flexible digital control inputs
Up to 2.1 A current from an ac charger in LDO mode
Operating input voltage from 4.0 V to 6.7 V
Tolerant input voltage from −0.5 V to +20 V (USB VBUS)
Fully compatible with USB 3.0 and USB Battery Charging
Specification 1.2
Built-in current sensing and limiting
As low as 54 mΩ battery isolation FET between battery and
charger output
Thermal regulation prevents overheating
Compliant with JEITA 1 and JEITA 2 Li-Ion battery charging
temperature specifications
SYS_EN flag permits the system to be disabled until battery is at
the minimum required level for guaranteed system start-up
APPLICATIONS
Digital still cameras
Digital video cameras
Single cell Li-Ion portable equipment
PDAs, audio, and GPS devices
Portable medical devices
Mobile phones
AC OR
USB
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
Linear Li-Ion Battery Charger with Power
Path and USB Compatibility in LFCSP
GENERAL DESCRIPTION
The
ADP5062
USB Battery Charging Specification 1.2 and enables charging
via the mini USB VBUS pin from a wall charger, car charger, or
USB host port.
The
ADP5062
but is tolerant of voltages up to 20 V thereby alleviating concerns
about USB bus spikes during disconnect or connect scenarios.
The
ADP5062
charger output and the battery. This permits battery isolation
and, hence, system powering under a dead battery or no battery
scenario, which allows for immediate system function on connec-
tion to a USB power supply.
Based on the type of USB source, which is detected by an external
USB detection chip, the
current limit for optimal charging and USB compliance.
The
ADP5062
put pins that provide maximum flexibility for different systems.
These digital input/output pins permit combinations of features
such as, input current limits, charging enable and disable, charging
current limits, and a dedicated interrupt output pin.
TYPICAL APPLICATION CIRCUIT
ADP5062
ISO_Sx
VBUS
VIN
CBP
C4
C1
10µF
10nF
SCL
SDA
ISO_Bx
CHARGER
BAT_SNS
CONTROL
DIG_IO1
BLOCK
DIG_IO2
DIG_IO3
THR
SYS_EN
ILED
AGND
Figure 1.
Document Feedback
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Technical Support
ADP5062
charger is fully compliant with USB 3.0 and the
operates from a 4 V to 6.7 V input voltage range
features an internal FET between the linear
ADP5062
can be set to apply the correct
has three factory-programmable digital input/out-
SYSTEM
C3
22µF
C2
22µF
Li-ion
+
VLED
©2012 Analog Devices, Inc. All rights reserved.
www.analog.com