ADP5062CP-EVALZ Analog Devices, ADP5062CP-EVALZ Datasheet - Page 35

• Manufacturer Part Number: ADP5062CP-EVALZ
• Description: Power Management IC Development Tools ADP5062 Evaluation board
• Manufacturer: Analog Devices
• Type: Linear Regulators - Standardr
• Series: ADP5062r

Specifications of ADP5062CP-EVALZ

• Rohs: yes
• Product: Evaluation Boards
• Tool Is For Evaluation Of: ADP5062
• Input Voltage: 4 V to 6.7 V
• Description/function: Battery charger (isolated flyback)
• Interface Type: I2C
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Output Current: 2.1 A
• Factory Pack Quantity: 1
• For Use With: ADP5062

Data Sheet
Table 33. IEND, Register Address 0x11
Bit No.
[7:5]
4
3
2
1:0
1
This option is active when VINx = 0 V and the battery monitor is activated from Register 0x07, Bit 5 (EN_BMON).
Bit Name
IEND[2:0]
C/20 EOC
C/10 EOC
C/5 EOC
SYS_EN_SET[1:0]
Access
R/W
R/W
R/W
R/W
R/W
Default
010 = 52.5 mA
0
0
0
00
Description
Termination current programming bus. The values of the termination current can
be programmed to the following values:
000 = 12.5 mA.
001 = 32.5 mA.
010 = 52.5 mA.
011 = 72.5 mA.
100 = 92.5 mA.
101 = 117.5 mA.
110 = 142.5 mA.
111 = 170.0 mA.
The C/20 EOC bit has priority over the other settings (C/5 EOC, C/10 EOC, and
IEND[2:0]).
1 = the termination current is ICHG[4:0] ÷ 20 with the following limitations:
Minimum value = 12.5 mA.
Maximum value = 170 mA.
The C/10 EOC bit has priority over the other termination current settings (C/5 EOC
and IEND[2:0]), but does not have priority over the C/20 EOC setting.
1 = the termination current is ICHG[4:0] ÷ 10, unless C/20 EOC is high. The
termination current is limited to the following values:
Minimum value = 12.5 mA.
Maximum value = 170 mA.
The C/5 EOC bit has priority over the other termination current settings (IEND[2:0])
but does not have priority over the C/20 EOC setting or the C/10 EOC setting.
1 = the termination current is ICHG[4:0] ÷ 5, unless the C/20 EOC or the C/10 EOC
bit is high. The termination current is limited to the following values:
Minimum value = 12.5 mA.
Maximum value = 170 mA.
Selects the operation of the system enable pin (SYS_EN).
00 = SYS_EN is activated when LDO is active and the system voltage is available.
01 = SYS_EN is activated by the ISO_Bx voltage, the battery charging mode.
10 = SYS_EN is activated and the isolation FET is disabled when the battery drops
below V
11 = SYS_EN is active in LDO mode when the charger is disabled. SYS_EN is active
in the charging mode when V
Rev. 0 | Page 35 of 44
WEAK
.
1
ISO_Bx
≥ V
WEAK
.
ADP5062