W25X32VSFIG T&R Winbond Electronics, W25X32VSFIG T&R Datasheet - Page 8

• Manufacturer Part Number: W25X32VSFIG T&R
• Description: IC FLASH 32MBIT 75MHZ 16SOIC
• Manufacturer: Winbond Electronics

Specifications of W25X32VSFIG T&R

• Format - Memory: FLASH
• Memory Type: FLASH
• Memory Size: 32M (4M x 8)
• Speed: 75MHz
• Interface: SPI Serial
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8.1
At the time this datasheet was published not all package types had been finalized. Contact Winbond
to confirm availability of these packages before designing to this specification. W25X16 and W25X32
are offered in an 8-pin plastic 208-mil width SOIC (package code SS). The W25X16 in 6x5-mm
WSON (package code ZP) and 25X32 and 25X64 in 8x6-mm WSON. (package code ZE). The 25X16,
W25X32 and W25X64 are offered in 16-pin plastic 300-mil width SOIC (package code SF) and 300-
mil DIP (package code DA). See figures 1a-d. Package diagrams and dimensions are illustrated at the
end of this datasheet.
8.2
The SPI Chip Select (/CS) pin enables and disables device operation. When /CS is high the device is
deselected and the Serial Data Output (DO) pin is at high impedance. When deselected, the devices
power consumption will be at standby levels unless an internal erase, program or status register cycle
is in progress. When /CS is brought low the device will be selected, power consumption will increase
to active levels and instructions can be written to and data read from the device. After power-up, /CS
must transition from high to low before a new instruction will be accepted. The /CS input must track
the VCC supply level at power-up (see “Write Protection” and figure 20). If needed a pull-up resister
on /CS can be used to accomplish this.
8.3
The SPI Serial Data Output (DO) pin provides a means for data and status to be serially read from
(shifted out of) the device. Data is shifted out on the falling edge of the Serial Clock (CLK) input pin.
8.4
The Write Protect (/WP) pin can be used to prevent the Status Register from being written. Used in
conjunction with the Status Register’s Block Protect (BP2, BP1, and BP0) bits and Status Register
Protect (SRP) bits, a portion or the entire memory array can be hardware protected. The /WP pin is
active low.
8.5
The /HOLD pin allows the device to be paused while it is actively selected. When /HOLD is brought
low, while /CS is low, the DO pin will be at high impedance and signals on the DIO and CLK pins will
be ignored (don’t care). When /HOLD is brought high, device operation can resume. The /HOLD
function can be useful when multiple devices are sharing the same SPI signals. (“See Hold function”)
8.6
The SPI Serial Clock Input (CLK) pin provides the timing for serial input and output operations. ("See
SPI Operations")
8.7
The SPI Serial Data Input/Output (DIO) pin provides a means for instructions, addresses and data to
be serially written to (shifted into) the device. Data is latched on the rising edge of the Serial Clock
(CLK) input pin. The DIO pin is also used as an output when the Fast Read Dual Output instruction is
executed.
Package Types
Chip Select (/CS)
Serial Data Output (DO)
Write Protect (/WP)
HOLD (/HOLD)
Serial Clock (CLK)
Serial Data Input / Output (DIO)
- 8 -
W25X16, W25X32, W25X64