MD2534-D2G-X-P SanDisk, MD2534-D2G-X-P Datasheet - Page 58

• Manufacturer Part Number: MD2534-D2G-X-P
• Description: IC MDOC H3 2GB FBGA
• Manufacturer: SanDisk

Specifications of MD2534-D2G-X-P

• Format - Memory: FLASH
• Memory Type: FLASH - Nand
• Memory Size: 2G (256M x 8)
• Interface: Parallel
• Voltage - Supply: 1.65 V ~ 1.95 V, 2.5 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 115-TFBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Speed: -

9.5
mDOC H3 can be configured to support different combinations of Core and IO host supply.
Table 4 lists the connectivity required for the support of the different available combinations.
9.6
9.6.1
When using a standard NOR-like interface, connect the control signals as follows:
• A[16:0] – Connect these signals to the host address signals (see Section 9.10 for
• D[15:0] – Connect these signals to the host data signals (see Section 9.10 for platform-related
• OE# (Output Enable) and Write Enable (WE#) – Connect these signals to the host RD# and
• CE# (Chip Enable) – Connect this signal to the memory address decoder. Most RISC/mobile
• RSTIN# (Power-On Reset In) – Connect this signal to the host active-low Power-On Reset
• ID0 (Chip Identification) – Connect this signal as shown in Figure 11. This signal must be
58
Core: 3.3V
IO: 3.3V
Core: 3.3V
IO: 1.8V
Core: 1.8V
IO: 1.8V
mDOC H3 Power
platform-related considerations). The A0 signal may be connected to either the host CPU A0
signal or to VSS.
considerations).
WR# signals, respectively.
processors include a programmable decoder to generate various Chip Select (CS) outputs for
different memory zones. These CS signals can be programmed to support different wait states
to accommodate mDOC H3 timing specifications.
signal.
connected to VSS if the host uses only one mDOC H3. If more than one device is being used,
refer to Section 9.9 for more information on device cascading.
Connecting Control Signals
H3 Power Supply Connectivity
Standard Interface
Supply
[2.5V-3.6V]
[1.65V-1.95V]
[1.65V-1.95V]
[1.65V-1.95V]
[2.7V-3.6V]
[2.7V-3.6V]
[1.65V-1.95V]
[2.7V-3.6V]
[2.7V-3.6V]
VCC
3.3V
3.3V
1.8V
Data Sheet (Preliminary) Rev. 0.2
Table 4: Power Connectivity
[1.65V-1.95V]
[1.65V-1.95V]
[2.5V-3.6V]
VCCQ
3.3V
1.8V
1.8V
1uF capacitor
1uF capacitor
Connect to a
Connect to a
[1.65V-1.95V]
to VSS
to VSS
VCC1
1.8V
Requires a 1uF
capacitor only
[2.7V-3.6V]
and 0.1uF
[2.7V-3.6V]
VCC2
3.3V
3.3V
mDOC H3 Embedded Flash Drive
Requires a 33nF
No Connection
No Connection
capacitor
92-DS-1205-10
C+, C-