CAT25080VI-G ON Semiconductor, CAT25080VI-G Datasheet

IC EEPROM 8KBIT 10MHZ 8SOIC

CAT25080VI-G

Manufacturer Part Number
CAT25080VI-G
Description
IC EEPROM 8KBIT 10MHZ 8SOIC
Manufacturer
ON Semiconductor
Datasheet

Specifications of CAT25080VI-G

Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
8K (1K x 8)
Speed
10MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Organization
1 K x 8
Interface Type
2-Wire
Maximum Clock Frequency
10 MHz
Access Time
5 ms
Supply Voltage (max)
5.5 V
Supply Voltage (min)
1.8 V
Maximum Operating Current
2 mA
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
1.8 V, 5.5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CAT25080VI-GT3
Quantity:
45
CAT25080, CAT25160
8-Kb and 16-Kb SPI Serial
CMOS EEPROM
Description
devices internally organized as 1024x8/2048x8 bits. They feature a
32−byte page write buffer and support the Serial Peripheral Interface
(SPI) protocol. The device is enabled through a Chip Select (CS)
input. In addition, the required bus signals are a clock input (SCK),
data input (SI) and data output (SO) lines. The HOLD input may be
used to pause any serial communication with the CAT25080/25160
device. These devices feature software and hardware write protection,
including partial as well as full array protection.
Features
© Semiconductor Components Industries, LLC, 2010
February, 2010 − Rev. 5
The CAT25080/25160 are 8−Kb/16−Kb Serial CMOS EEPROM
− Protect 1/4, 1/2 or Entire EEPROM Array
Compliant
10 MHz SPI Compatible
1.8 V to 5.5 V Supply Voltage Range
SPI Modes (0,0) & (1,1)
32−byte Page Write Buffer
Self−timed Write Cycle
Hardware and Software Protection
Block Write Protection
Low Power CMOS Technology
1,000,000 Program/Erase Cycles
100 Year Data Retention
Industrial and Extended Temperature Range
8−lead PDIP, SOIC, TSSOP and 8−pad TDFN, UDFN Packages
These Devices are Pb−Free, Halogen Free/BFR Free, and RoHS
HOLD
SCK
WP
CS
SI
Figure 1. Functional Symbol
CAT25080
CAT25160
V
V
CC
SS
SO
1
See detailed ordering and shipping information in the package
dimensions section on page 16 of this data sheet.
CASE 751BD
V SUFFIX
Pin Name
SOIC−8
HOLD
SCK
V
V
WP
SO
CS
SI
SS
CC
PDIP (L), SOIC (V), TSSOP (Y),
ORDERING INFORMATION
V
CASE 646AA
WP
CS
SO
SS
L SUFFIX
TDFN (VP2), UDFN (HU2)
PIN CONFIGURATION
PDIP−8
http://onsemi.com
PIN FUNCTION
CASE 517AW
HU2 SUFFIX
Chip Select
Serial Data Output
Write Protect
Ground
Serial Data Input
Serial Clock
Hold Transmission Input
Power Supply
UDFN−8
1
Publication Order Number:
CASE 948AL
TSSOP−8
Y SUFFIX
Function
CASE 511AK
V
HOLD
SCK
SI
VP2 SUFFIX
CC
CAT25080/D
TDFN−8

Related parts for CAT25080VI-G

CAT25080VI-G Summary of contents

Page 1

CAT25080, CAT25160 8-Kb and 16-Kb SPI Serial CMOS EEPROM Description The CAT25080/25160 are 8−Kb/16−Kb Serial CMOS EEPROM devices internally organized as 1024x8/2048x8 bits. They feature a 32−byte page write buffer and support the Serial Peripheral Interface (SPI) protocol. The device ...

Page 2

Table 1. ABSOLUTE MAXIMUM RATINGS Operating Temperature Storage Temperature Voltage on any Pin with Respect to Ground (Note 1) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions ...

Page 3

Table 5. A.C. CHARACTERISTICS Symbol Parameter f Clock Frequency SCK t Data Setup Time SU t Data Hold Time H t SCK High Time WH t SCK Low Time WL t HOLD to Output Low (Note 5) ...

Page 4

... The BP0 and BP1 (Block Protect) bits determine which blocks are currently write protected. They are set by the user with the WRSR command and are non−volatile. The user is allowed to protect a quarter, one half or the entire memory, by setting these bits according to Table 9. The protected blocks then become read−only. ...

Page 5

Table 8. STATUS REGISTER WPEN 0 0 Table 9. BLOCK PROTECTION BITS Status Register Bits BP1 BP0 Table 10. WRITE PROTECT CONDITIONS WPEN ...

Page 6

... The CAT25080/160 device powers up into a write disable state. The device contains a Write Enable Latch (WEL) which must be set before attempting to write to the memory array or to the status register. In addition, the address of the memory location( written must be outside the protected area, as defined by BP0 and BP1 bits from the status register ...

Page 7

Byte Write Once the WEL bit is set, the user may execute a write sequence, by sending a WRITE instruction, a 16−bit address and data as shown in Figure 5. Only 10 significant address bits are used by the CAT25080 ...

Page 8

Write Status Register The Status Register is written by sending a WRSR instruction according to timing shown in Figure 7. Only bits 2, 3 and 7 can be written using the WRSR command SCK OPCODE ...

Page 9

... Read from Memory Array To read from memory, the host sends a READ instruction followed by a 16−bit address (see Table 11 for the number of significant address bits). After receiving the last address bit, the CAT25080/160 will respond by shifting out data on the SO pin (as shown in Figure 9). Sequentially stored data can be read out by simply continuing to run the clock ...

Page 10

... The CS input must be set high after the proper number of clock cycles to start the internal write cycle. Access to the memory array during an internal write cycle is ignored and programming is continued. Any invalid op−code will be ignored and the serial output pin (SO) will drops remain in the high impedance state ...

Page 11

PIN # 1 IDENTIFICATION D TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MS-001. PACKAGE DIMENSIONS PDIP−8, 300 mils CASE 646AA−01 ISSUE A SYMBOL ...

Page 12

PIN # 1 IDENTIFICATION TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-012. PACKAGE DIMENSIONS SOIC 8, 150 mils CASE 751BD−01 ISSUE O SYMBOL ...

Page 13

E1 e TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-153. PACKAGE DIMENSIONS TSSOP8, 4.4x3 CASE 948AL−01 ISSUE O SYMBOL MIN A A1 0.05 A2 ...

Page 14

D E PIN#1 INDEX AREA TOP VIEW SYMBOL MIN NOM A 0.70 0.75 A1 0.00 0.02 A2 0.45 0.55 A3 0.20 REF b 0.20 0.25 D 1.90 2.00 D2 1.30 1.40 E 2.90 3.00 E2 1.20 1.30 e 0.50 TYP ...

Page 15

D E PIN #1 INDEX AREA TOP VIEW SYMBOL MIN NOM A 0.45 0.50 A1 0.00 0.02 b 0.18 0.25 D 1.90 2.00 D2 1.50 1.60 E 1.90 2.00 E2 0.80 0.90 e 0.50 BSC L 0.20 0.30 Notes: (1) ...

Page 16

... The device used in the above example is a CAT25160VI−GT3 (SOIC, Industrial Temperature, NiPdAu, Tape & Reel, 3,000/Reel). 12. For additional package and temperature options, please contact your nearest ON Semiconductor Sales office. 13. For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D ...

Related keywords