LNK306PN Power Integrations, LNK306PN Datasheet - Page 5

IC OFFLINE SWIT OCP 8DIP

LNK306PN

Manufacturer Part Number
LNK306PN
Description
IC OFFLINE SWIT OCP 8DIP
Manufacturer
Power Integrations
Series
LinkSwitch®-TNr
Type
Off Line Switcherr
Datasheet

Specifications of LNK306PN

Output Isolation
Non-Isolated
Frequency Range
62 ~ 70kHz
Voltage - Output
700V
Power (watts)
12mW
Operating Temperature
-40°C ~ 150°C
Package / Case
8-DIP (0.300", 7.62mm), 7 Leads
Output Voltage
12 V
Input / Supply Voltage (max)
265 VAC
Input / Supply Voltage (min)
85 VAC
Duty Cycle (max)
72 %
Switching Frequency
66 KHz
Supply Current
250 uA
Operating Temperature Range
- 40 C to + 150 C
Mounting Style
Through Hole
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
596-1027-5

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LNK306PN
Manufacturer:
POWER
Quantity:
3 000
Part Number:
LNK306PN
Manufacturer:
PowerInt
Quantity:
9 750
Part Number:
LNK306PN
Manufacturer:
POWER
Quantity:
20 000
Part Number:
LNK306PN
0
Company:
Part Number:
LNK306PN
Quantity:
18 000
Figure 6a. Recommended Printed Circuit Layout for LinkSwitch-TN in a Buck Converter Confi guration using P or G Package.
Figure 6b. Recommended Printed Circuit Layout for LinkSwitch-TN in a Buck Converter Confi guration using D Package
cycles are skipped. To provide overload protection if no cycles
are skipped during a 50 ms period, LinkSwitch-TN will enter
auto-restart (LNK304-306), limiting the average output power
to approximately 6% of the maximum overload power. Due to
tracking errors between the output voltage and the voltage across
C3 at light load or no load, a small pre-load may be required
(R4). For the design in Figure 5, if regulation to zero load is
required, then this value should be reduced to 2.4 kΩ.
Key Application Considerations
LinkSwitch-TN Design Considerations
Output Current Table
Data sheet maximum output current table (Table 1) represents
the maximum practical continuous output current for both
mostly discontinuous conduction mode (MDCM) and continuous
conduction mode (CCM) of operation that can be delivered from
a given LinkSwitch-TN device under the following assumed
conditions:
INPUT
Optimize hatched copper areas (
AC
INPUT
AC
to Bottom Side of the Board.
RF1
RF1
D4
D4
D3
D3
C4
C4
) for heatsinking and EMI.
L2
L2
C5
Optimize hatched copper areas (
C5
FB
BP
D
S
S
D
LinkSwitch-TN
C1
1) Buck converter topology.
2) The minimum DC input voltage is ≥70 V. The value of
3) For CCM operation a KRP* of 0.4.
4) Output voltage of 12 VDC.
5) Effi ciency of 75%.
6) A catch/freewheeling diode with t
7) The part is board mounted with SOURCE pins soldered
*KRP is the ratio of ripple to peak inductor current.
LinkSwitch-TN Selection and Selection Between
MDCM and CCM Operation
Select the LinkSwitch-TN device, freewheeling diode and output
inductor that gives the lowest overall cost. In general, MDCM
input capacitance should be large enough to meet this
criterion.
MDCM operation and for CCM operation, a diode with
t
to a suffi cient area of copper to keep the SOURCE pin
temperature at or below 100 °C.
rr
S
S
S
S
≤35 ns is used.
R3
) for heatsinking and EMI.
FB
BP
S
S
D1
R1
C1
C3
R3
L1
R1
LNK302/304-306
C3
D2
D1
rr
≤75 ns is used for
PI-4546-011807
C2
L1
D2
C2
PI-3750-121106
OUTPUT
OUTPUT
DC
DC
Rev. I 11/08
2-5
5
+
+

Related parts for LNK306PN