VIPER25HDTR STMicroelectronics, VIPER25HDTR Datasheet - Page 32

no-image

VIPER25HDTR

Manufacturer Part Number
VIPER25HDTR
Description
IC OFFLINE CONV PWM OVP 16SOIC
Manufacturer
STMicroelectronics
Series
VIPer™ plusr
Datasheet

Specifications of VIPER25HDTR

Output Isolation
Isolated
Frequency Range
200 ~ 250kHz
Voltage - Input
8.5 ~ 23.5 V
Voltage - Output
800V
Power (watts)
24W
Operating Temperature
-40°C ~ 150°C
Package / Case
16-SOIC (0.154", 3.90mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-10066-2

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
VIPER25HDTR
Manufacturer:
ST
Quantity:
24 356
Part Number:
VIPER25HDTR
Manufacturer:
ST
0
Operation description
7.14
7.15
32/40
Burst-mode operation at no load or very light load
When the load decrease the feedback loop reacts lowering the feedback pin voltage. If it
falls down the burst mode threshold, V
switched on. After the MOSFET stops, as a result of the feedback reaction to the energy
delivery stop, the feedback pin voltage increases and exceeding the level, V
V
reported on
where power MOSFET is switching to period of time where power MOSFET is not switching;
this device working mode is the burst mode. The power delivered to output during switching
periods exceeds the load power demands; the excess of power is balanced from not
switching period where no power is processed. The advantage of burst mode operation is
an average switching frequency much lower then the normal operation working frequency,
up to some hundred of hertz, minimizing all frequency related losses. During the burst-mode
the drain current peak is clamped to the level, I
Figure 37. Burst mode timing diagram, light load management
Brown-out protection
Brown-out protection is a not-latched shutdown function activated when a condition of mains
under voltage is detected. The Brown-out comparator is internally referenced to V
threshold, see
is below this internal reference. Under this condition the power MOSFET is turned off. Until
the Brown out condition is present, the V
V
voltage hysteresis is present to improve the noise immunity.
The switching operation is restarted as the voltage on the pin is above the reference plus the
before said voltage hysteresis. See
The Brown-out comparator is provided also with a current hysteresis, I
has to set the rectified input voltage above which the power MOSFET starts switching after
brown out event, V
switched off, V
be set separately.
FBbmhys
DDon
V
FBbm
and the UVLO thresholds, as shown in the timing diagram of
+V
, the power MOSFET starts switching again. The burst mode thresholds are
V
FBbmhys
V
I
COMP
DRAIN
I
FBbm
D_BM
I
I
I
DD
DD1
DD0
Table 8
INoff
Table 8 on page 8
. Thanks to the I
INon
and
, and the rectified input voltage below which the power MOSFET is
Figure 37
Doc ID 15585 Rev 4
, and disables the PWM if the voltage applied at the BR pin
BRhyst
shows this behavior. Systems alternates period of time
Figure 5 on page 10
FBbm
, see
DD
, the power MOSFET is not more allowed to be
voltage continuously oscillates between the
Table 8 on page 8
Burst Mode
D_BM
, reported on
.
, these two thresholds can
Table 8
Figure 38 on page 33
BRhyst
.
FBbm
. The designer
+
BRth
VIPER25
time
time
time
. A

Related parts for VIPER25HDTR