TNY266PN Power Integrations, TNY266PN Datasheet - Page 5

IC OFFLINE SWIT OTP OCP HV 8DIP

TNY266PN

Manufacturer Part Number
TNY266PN
Description
IC OFFLINE SWIT OTP OCP HV 8DIP
Manufacturer
Power Integrations
Series
TinySwitch®-IIr
Datasheets

Specifications of TNY266PN

Output Isolation
Isolated
Frequency Range
124 ~ 140kHz
Voltage - Output
700V
Power (watts)
15W
Operating Temperature
-40°C ~ 150°C
Package / Case
8-DIP (0.300", 7.62mm), 7 Leads
Output Voltage
5.8 V
Input / Supply Voltage (max)
265 VAC
Input / Supply Voltage (min)
85 VAC
Duty Cycle (max)
68 %
Switching Frequency
132 KHz
Supply Current
265 uA
Operating Temperature Range
- 40 C to + 150 C
Mounting Style
Through Hole
Supply Voltage
265VAC
Digital Ic Case Style
DIP
No. Of Pins
8
No. Of Regulated Outputs
1
Filter Terminals
DIP
Rohs Compliant
Yes
On Resistance Rds(on)
14ohm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
596-1051-5

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TNY266PN
Manufacturer:
PHILIPS
Quantity:
3 000
Part Number:
TNY266PN
Manufacturer:
PowerInt
Quantity:
84 450
Part Number:
TNY266PN
Manufacturer:
POWER/PBF
Quantity:
31
Part Number:
TNY266PN
Manufacturer:
POWER
Quantity:
20 000
Part Number:
TNY266PN
Manufacturer:
POWER
Quantity:
11 868
Part Number:
TNY266PN
Manufacturer:
POWER
Quantity:
15 719
Part Number:
TNY266PN
Manufacturer:
POWER
Quantity:
3 808
Part Number:
TNY266PN
0
Company:
Part Number:
TNY266PN
Quantity:
10 000
the SOURCE pin. The optocoupler LED is connected in series
with a Zener diode across the DC output voltage to be regulated.
When the output voltage exceeds the target regulation voltage
level (optocoupler LED voltage drop plus Zener voltage), the
optocoupler LED will start to conduct, pulling the EN/UV pin
low. The Zener diode can be replaced by a TL431 reference
circuit for improved accuracy.
ON/OFF Operation with Current Limit State Machine
The internal clock of the TinySwitch-II runs all the time. At
Figure 7. TinySwitch-II Operation at Moderately Heavy Loading.
Figure 6. TinySwitch-II Operation at Near Maximum Loading.
V
V
I
I
CLOCK
CLOCK
DRAIN
DRAIN
D
DRAIN
D
DRAIN
MAX
MAX
V
V
EN
EN
PI-2667-090700
PI-2749-050301
the beginning of each clock cycle, it samples the EN/UV pin to
decide whether or not to implement a switch cycle, and based
on the sequence of samples over multiple cycles, it determines
the appropriate current limit. At high loads, when the EN/UV
pin is high (less than 240 µA out of the pin), a switching cycle
with the full current limit occurs. At lighter loads, when EN/UV
is high, a switching cycle with a reduced current limit occurs.
At near maximum load, TinySwitch-II will conduct during nearly
all of its clock cycles (Figure 6). At slightly lower load, it will
“skip” additional cycles in order to maintain voltage regulation
at the power supply output (Figure 7). At medium loads, cycles
will be skipped and the current limit will be reduced (Figure 8).
At very light loads, the current limit will be reduced even further
(Figure 9). Only a small percentage of cycles will occur to
satisfy the power consumption of the power supply.
The response time of the TinySwitch-II ON/OFF control scheme
is very fast compared to normal PWM control. This provides
tight regulation and excellent transient response.
Power Up/Down
The TinySwitch-II requires only a 0.1 µF capacitor on the
BYPASS pin. Because of its small size, the time to charge this
capacitor is kept to an absolute minimum, typically 0.6 ms. Due
to the fast nature of the ON/OFF feedback, there is no overshoot
at the power supply output. When an external resistor (2 MΩ)
is connected from the positive DC input to the EN/UV pin, the
power MOSFET switching will be delayed during power-up until
the DC line voltage exceeds the threshold (100 V). Figures 10
and 11 show the power-up timing waveform of TinySwitch-II
in applications with and without an external resistor (2 MΩ)
connected to the EN/UV pin.
Figure 8. TinySwitch-II Operation at Medium Loading.
V
I
CLOCK
D
DRAIN
DRAIN
MAX
V
EN
TNY263-268
PI-2377-091100
4/05
G
5

Related parts for TNY266PN