TNY253P Power Integrations, TNY253P Datasheet
TNY253P
Specifications of TNY253P
Available stocks
Related parts for TNY253P
TNY253P Summary of contents
Page 1
... DRAIN spike ® Family Wide-Range HV DC Input Figure 1. Typical Standby Application. ORDER PART NUMBER TNY253P TNY253G TNY254P TNY254G TNY255P TNY255G Table 1. *Please refer to the Key Application Considerations section for details. voltage. At the same time, they allow use of low cost EE16 core transformers to deliver ...
Page 2
TNY253/254/255 BYPASS 50 A OSCILLATOR CLOCK DC MAX 1 ENABLE Figure 2. Functional Block Diagram. Pin Functional Description DRAIN (D) Pin: Power MOSFET drain connection. Provides internal operating current for both start-up and steady-state operation. BYPASS ...
Page 3
Clock signal (at the beginning of each cycle high, then the power MOSFET is turned on (enabled) for that cycle, otherwise the power MOSFET remains in the ...
Page 4
TNY253/254/255 V EN CLOCK DC MAX I DRAIN V DRAIN Figure 4. TinySwitch Operation at Heavy Load. percentage of cycles will conduct to support the power consumption of the power supply. The response time of TinySwitch ON/OFF control scheme is ...
Page 5
V EN CLOCK DC MAX I DRAIN V DRAIN Figure 6. TinySwitch Operation at Light Load. 130 kHz Switching Frequency (TNY255) The switching frequency (with no cycle skipping) is set at 130 kHz. This allows the TNY255 to deliver 10 ...
Page 6
... DC supply to the inputs of the standby circuit. The high voltage DC bus is applied to the primary winding series with the integrated high voltage D 6 4/03 D1 1N4934 TinySwitch R1 D 100 Ω 1/2 W TNY253P 0.1 µ 680 pF Y1 Safety D2 SB540 4700 ...
Page 7
... Y1 Safety TinySwitch 2 200 V TNY253P 0 100 create a high voltage DC bus connected series with the high voltage MOSFET inside the TNY254. The inductor L1 forms a π-filter in conjunction with C1 and C2. The resistor R1 damps resonances in the inductor L1. The low frequency of operation of TNY254 (44 kHz) allows use of the simple π-filter described above in combination with a single Y1-capacitor C8 to meet worldwide conducted EMI standards ...
Page 8
TNY253/254/255 is provided by L2 and C6. The output voltage is determined by the sum of the optocoupler U2 LED forward drop (~ 1 V) and Zener diode VR1 voltage. The resistor R8, maintains a bias current through the Zener ...
Page 9
Input Filter Capacitor + HV – S TOP VIEW TinySwitch Figure 13. Recommended PC Layout for the TinySwitch. accommodated by rating the output diode to handle the short circuit current. The short circuit current can be ...
Page 10
TNY253/254/255 DRAIN Voltage ....................................... - 0 700 V Peak DRAIN Current (TNY253/4) ........................400 mA Peak DRAIN Current (TNY255) ...........................530 mA ENABLE Voltage ........................................ - 0 ENABLE Current ...................................................100 mA BYPASS Voltage .......................................... -0.3 V ...
Page 11
Parameter Symbol CIRCUIT PROTECTION Current Limit I LIMIT Note F Initial Current I Limit INIT Leading Edge t Blanking Time LEB Current Limit t Delay ILD Thermal Shutdown Temperature Thermal Shutdown Hysteresis OUTPUT ON-State R DS(ON) Resistance OFF-State Drain I ...
Page 12
TNY253/254/255 Parameter Symbol OUTPUT (cont.) DRAIN Supply Voltage Output Enable t Delay EN Output Disable t Setup Time DST NOTES: A. For a threshold with a negative value, negative hysteresis is a decrease in magnitude of the corresponding threshold. B. ...
Page 13
HV 90% DRAIN VOLTAGE 10 Figure 15. TinySwitch Duty Cycle Measurement. Typical Performance Characteristics BREAKDOWN vs. TEMPERATURE 1.1 1.0 0.9 -50 - 100 125 150 Junction Temperature (°C) DC MAX ...
Page 14
TNY253/254/255 Typical Performance Characteristics (Continued) CURRENT LIMIT vs. TEMPERATURE 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -50 - Junction Temperature (°C) TNY254 CURRENT LIMIT vs. di/dt 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 ...
Page 15
Typical Performance Characteristics (Continued) C OSS vs. DRAIN VOLTAGE 100 200 DRAIN Voltage (V) DIM inches mm A 0.367-0.387 9.32-9.83 B 0.240-0.260 6.10-6.60 C 0.125-0.145 3.18-3.68 G 0.015-0.040 0.38-1.02 H 0.120-0.140 3.05-3.56 J1 0.057-0.068 1.45-1.73 J2 0.014-0.022 ...
Page 16
TNY253/254/255 D S .004 (.10 - G08A .010 (.25 4/03 SMD-8 .046 .060 .060 .046 Pin 1 .086 .186 -D- .286 ...
Page 17
Notes TNY253/254/255 D 17 4/03 ...
Page 18
TNY253/254/255 D 18 4/03 Notes ...
Page 19
Notes TNY253/254/255 D 19 4/03 ...
Page 20
... PATENT INFORMATION Power Integrations reserves the right to make changes to its products at any time to improve reliability or manufacturability. Power Integrations does not assume any liability arising from the use of any device or circuit described herein, nor does it convey any license under its patent rights or the rights of others. ...