TOP242F Power Integrations, TOP242F Datasheet - Page 5

IC OFFLINE SWIT UVLO HV TO262

TOP242F

Manufacturer Part Number
TOP242F
Description
IC OFFLINE SWIT UVLO HV TO262
Manufacturer
Power Integrations
Series
TOPSwitch®-GXr
Datasheet

Specifications of TOP242F

Output Isolation
Isolated
Frequency Range
66 ~ 132kHz
Voltage - Output
700V
Power (watts)
22W
Operating Temperature
-40°C ~ 150°C
Package / Case
TO-262-7 (Formed Leads), 5 Leads
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TOP242F
Manufacturer:
MICRON
Quantity:
147
Part Number:
TOP242F
Manufacturer:
POWER
Quantity:
20 000
Part Number:
TOP242FN
Manufacturer:
POWER
Quantity:
15 000
Part Number:
TOP242FN
Manufacturer:
POWER
Quantity:
20 000
Company:
Part Number:
TOP242FN
Quantity:
58 000
TOPSwitch-GX Family Functional
Description
Like TOPSwitch, TOPSwitch-GX is an integrated switched
mode power supply chip that converts a current at the control
input to a duty cycle at the open drain output of a high voltage
power MOSFET. During normal operation the duty cycle
of the power MOSFET decreases linearly with increasing
CONTROL pin current as shown in Figure 7.
In addition to the three terminal TOPSwitch features, such as
the high voltage start-up, the cycle-by-cycle current limiting,
loop compensation circuitry, auto-restart, thermal shutdown,
the TOPSwitch-GX incorporates many additional functions that
reduce system cost, increase power supply performance and
design flexibility. A patented high voltage CMOS technology
allows both the high voltage power MOSFET and all the low
voltage control circuitry to be cost effectively integrated onto
a single monolithic chip.
Three terminals, FREQUENCY, LINE-SENSE, and
EXTERNAL CURRENT LIMIT (available in Y, R or F
package) or one terminal MULTI-FUNCTION (available in P
or G package) have been added to implement some of the new
functions. These terminals can be connected to the SOURCE
pin to operate the TOPSwitch-GX in a TOPSwitch-like three
terminal mode. However, even in this three terminal mode, the
TOPSwitch-GX offers many new transparent features that do
not require any external components:
1. A fully integrated 10 ms soft-start limits peak currents
2. DC
3. Frequency reduction at light loads lowers the switching
4. Higher switching frequency of 132 kHz reduces the
5. Frequency jittering reduces EMI.
6. Hysteretic over-temperature shutdown ensures automatic
7. Packages with omitted pins and lead forming provide large
8. Tighter absolute tolerances and smaller temperature
The LINE-SENSE (L) pin is usually used for line sensing by
connecting a resistor from this pin to the rectified DC high
voltage bus to implement line overvoltage (OV), under-voltage
(UV) and line feed-forward with DC
mode, the value of the resistor determines the OV/UV thresholds
and the DC
above the under-voltage threshold. See Table 2 and Figure 11.
and voltages during start-up and dramatically reduces or
eliminates output overshoot in most applications.
input voltage requirement and/or higher power capability.
losses and maintains good cross regulation in multiple output
supplies.
transformer size with no noticeable impact on EMI.
recovery from thermal fault. Large hysteresis prevents
circuit board overheating.
drain creepage distance.
variations on switching frequency, current limit and PWM gain.
MAX
of 78% allows smaller input storage capacitor, lower
MAX
is reduced linearly starting from a line voltage
MAX
reduction. In this
Figure 7. Relationship of Duty Cycle and Frequency to CONTROL
The pin can also be used as a remote ON/OFF and a
synchronization input.
The EXTERNAL CURRENT LIMIT (X) pin is usually used
to reduce the current limit externally to a value close to the
operating peak current, by connecting the pin to SOURCE
through a resistor. This pin can also be used as a remote
ON/OFF and a synchronization input in both modes. See
Table 2 and Figure 11.
For the P or G packages the LINE-SENSE and EXTERNAL
CURRENT LIMIT pin functions are combined on one MULTI-
FUNCTION (M) pin. However, some of the functions become
mutually exclusive as shown in Table 3.
The FREQUENCY (F) pin in the Y, R or F package sets the
switching frequency to the default value of 132 kHz when
connected to SOURCE pin. A half frequency option of
66 kHz can be chosen by connecting this pin to CONTROL pin
instead. Leaving this pin open is not recommended.
132
30
78
38
10
Auto-restart
Auto-restart
TOP242-5 1.6 2.0
TOP246-9 2.2 2.6
TOP250
Pin Current.
Note: For P and G packages I
I
I
CD1
CD1
2.4 2.7
I
L
= 190 µA
I
I
B
B
I
L
= 190 µA
I
I
C
C
(mA)
(mA)
Slope = PWM Gain
L
is replaced with I
I
L
TOP242-250
= 125 µA
I
L
= 125 µA
5.2
5.8
6.5
I
L
11/05
PI-2633-011502
< I
M
L(DC)
O
I
.
L
6.0
6.6
7.3
< I
L(DC)
5

Related parts for TOP242F