NCP1207DR2G ON Semiconductor, NCP1207DR2G Datasheet

no-image

NCP1207DR2G

Manufacturer Part Number
NCP1207DR2G
Description
IC CTRLR PWM CM OVP OCP HV 8SOIC
Manufacturer
ON Semiconductor
Datasheet

Specifications of NCP1207DR2G

Output Isolation
Isolated
Voltage - Input
10.6 ~ 16 V
Operating Temperature
-40°C ~ 150°C
Package / Case
8-SOIC (0.154", 3.90mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
NCP1207DR2GOS

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
NCP1207DR2G
Manufacturer:
ON
Quantity:
5 000
NCP1207
PWM Current−Mode
Controller for Free Running
Quasi−Resonant Operation
demagnetization detector to ensure full borderline/critical
Conduction Mode in any load/line conditions and minimum drain
voltage switching (Quasi−Resonant operation). Due to its inherent skip
cycle capability, the controller enters burst mode as soon as the power
demand falls below a predetermined level. As this happens at low peak
current, no audible noise can be heard. An internal 8.0 ms timer prevents
the free−run frequency to exceed 100 kHz (therefore below the 150 kHz
CISPR−22 EMI starting limit), while the skip adjustment capability lets
the user select the frequency at which the burst foldback takes place.
transformer design in avoiding the use of an auxiliary winding to supply
the NCP1207. This feature is particularly useful in applications where
the output voltage varies during operation (e.g. battery chargers). Due to
its high−voltage technology, the IC is directly connected to the
high−voltage DC rail. As a result, the short−circuit trip point is not
dependent upon any V
winding which, brought via a dedicated pin, also enables fast
Overvoltage Protection (OVP). Once an OVP has been detected, the IC
permanently latches off.
an Overcurrent Fault Protection (OCP) circuitry makes the final design
rugged and reliable.
Features
Typical Applications
*For additional information on our Pb−Free strategy and soldering details, please
October, 2004 − Rev. 8
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
The NCP1207 combines a true current mode modulator and a
The Dynamic Self−Supply (DSS) drastically simplifies the
The transformer core reset detection is done through an auxiliary
Finally, the continuous feedback signal monitoring implemented with
Pb−Free Packages are Available*
Free−Running Borderline/Critical Mode Quasi−Resonant Operation
Current−Mode with Adjustable Skip−Cycle Capability
No Auxiliary Winding V
Auto−Recovery Overcurrent Protection
Latching Overvoltage Protection
External Latch Triggering, e.g. Via Overtemperature Signal
500 mA Peak Current Source/Sink Capability
Internal 1.0 ms Soft−Start
Internal 8.0 ms Minimum T
Adjustable Skip Level
Internal Temperature Shutdown
Direct Optocoupler Connection
SPICE Models Available for TRANsient Analysis
AC−DC Adapters for Notebooks, etc.
Offline Battery Chargers
Consumer Electronics (DVD Players, Set−Top Boxes, TVs, etc.)
Auxiliary Power Supplies (USB, Appliances, TVs, etc.)
Semiconductor Components Industries, LLC, 2004
CC
auxiliary level.
CC
OFF
Operation
1
†For information on tape and reel specifications,
NCP1207DR2
NCP1207DR2G
NCP1207P
NCP1207PG
8
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
8
Device
1
1
ORDERING INFORMATION
DMG
GND
CS
FB
1207/P = Device Code
A
WL, L
YY, Y
WW, W = Work Week
PIN CONNECTIONS
http://onsemi.com
D1, D2 SUFFIX
1
2
3
4
(Pb−Free)
(Pb−Free)
Package
SOIC−8
PDIP−8
PDIP−8
CASE 751
CASE 626
SOIC−8
N SUFFIX
(Top View)
SOIC−8
PDIP−8
= Assembly Location
= Wafer Lot
= Year
Publication Order Number:
8
7
6
5
2500/Tape & Reel
2500/Tape & Reel
50 Units/Tube
50 Units/Tube
8
1
HV
NC
V
Drv
DIAGRAMS
8
1
Shipping
MARKING
CC
NCP1207/D
ALYW
1207
YYWW
1207P
AWL

Related parts for NCP1207DR2G

NCP1207DR2G Summary of contents

Page 1

... CS 4 GND (Top View) ORDERING INFORMATION Device Package NCP1207DR2 SOIC−8 NCP1207DR2G SOIC−8 (Pb−Free) NCP1207P PDIP−8 NCP1207PG PDIP−8 (Pb−Free) †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D ...

Page 2

Universal Network *Please refer to the application information section PIN FUNCTION DESCRIPTION Pin No. Pin Name Function 1 Demag Core reset detection and OVP 2 FB Sets the peak current setpoint 3 CS Current sense input and skip cycle ...

Page 3

HV 7.0 PON mA 5 − 5.3 V (fault) To Internal Fault Supply Mngt. GND *S and R are level triggered whereas S is edge triggered. R has priority over the ...

Page 4

ELECTRICAL CHARACTERISTICS unless otherwise noted) CC Rating DYNAMIC SELF−SUPPLY V Increasing Level at which the Current Source Turns−off CC V Decreasing Level at which the Current Source Turns− Decreasing Level at which the Latchoff ...

Page 5

TEMPERATURE ( C) Figure 3. V Increasing Level at which the CC Current Source Turns−off versus Temperature 1.60 1.40 1.20 1.00 0.80 0.60 0.40 −50 −25 ...

Page 6

TEMPERATURE ( C) Figure 9. Source Resistance versus Temperature 120 100 −50 − TEMPERATURE ( C) Figure 11. ...

Page 7

TEMPERATURE ( C) Figure 13. Minimum T versus Temperature off −50 Figure 15. DMG Pin Internal Resistance versus NCP1207 TYPICAL CHARACTERISTICS ...

Page 8

... Conduction Mode (BCM) also called Critical Conduction Mode. Dynamic Self−Supply (DSS): due to its Very High Voltage Integrated Circuit (VHVIC) technology, ON Semiconductor’s NCP1207 allows for a direct pin connection to the high−voltage DC rail. A dynamic current source charges up a capacitor and thus provides a fully independent V level to the NCP1207 ...

Page 9

The DSS behavior actually depends on the internal IC consumption and the MOSFET’s gate charge Qg select a MOSFET like the MTP2N60E, Qg equals 22 nC (max). With a maximum switching frequency selected at 75 kHz, the average ...

Page 10

DRIVER DRIVER = HIGH ? DRIVER = LOW ? I = 200 mA − 3 RESET + 2 + Figure 19. A patented method allows for skip level selection via a series resistor inserted in series with ...

Page 11

Demagnetization Detection The core reset detection is done by monitoring the voltage activity on the auxiliary winding. This voltage features a FLYBACK polarity. The typical detection level is fixed exemplified by Figure 21. 7.0 POSSIBLE 5.0 ...

Page 12

Latching Off the NCP1207 In certain cases, it can be very convenient to externally shut down permanently the NCP1207 via a dedicated signal, e.g. coming from a temperature sensor. The reset occurs when the user unplugs the power supply from ...

Page 13

If the power consumption budget is really too high for the DSS alone, connect a diode between the auxiliary winding and the V pin which will disable the DSS V). operation (V CC The SOIC package offers ...

Page 14

Calculating the V Capacitor CC As the above section describes, the fall down sequence depends upon the V level: how long does it take for the CC V line to go from The required time ...

Page 15

V (5 V/div) V GATE Rsense 200 SKIP Current Sense Pin (200 mV/div) Figure 31. This picture explains how the 200 mA internal offset current creates the skip cycle level. NCP1207 V (200 mV/div) CC The short−circuit ...

Page 16

... G C SEATING PLANE −Z− 0.25 (0.010 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NCP1207 PACKAGE DIMENSIONS SOIC−8 D1, D2 SUFFIX CASE 751−07 ISSUE 0.10 (0.004) ...

Page 17

F −A− NOTE 2 C −T− N SEATING PLANE 0.13 (0.005) M NCP1207 PACKAGE DIMENSIONS PDIP−8 N SUFFIX CASE 626−05 ISSUE http://onsemi.com ...

Page 18

... Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com NCP1207 N. American Technical Support: 800−282−9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 http://onsemi.com 18 ON Semiconductor Website: http://onsemi ...

Related keywords