MCP73838T-FCI/MF Microchip Technology, MCP73838T-FCI/MF Datasheet - Page 16

• Manufacturer Part Number: MCP73838T-FCI/MF
• Description: IC LIION CHRGR USB/AC-IN 10DFN
• Manufacturer: Microchip Technology

Specifications of MCP73838T-FCI/MF

• Battery Type: Lithium-Ion (Li-Ion), Lithium-Polymer (Li-Pol)
• Function: Charge Management
• Voltage - Supply: 4.5 V ~ 6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 10-DFN
• Input Voltage: 6V
• Battery Charge Voltage: 4.5V
• Charge Current Max: 1A
• Battery Ic Case Style: DFN
• No. Of Pins: 10
• No. Of Series Cells: 1
• Product: Charge Management
• Output Voltage: 4.2 V, 4.35 V, 4.4 V, 4.5 V
• Output Current: 1200 mA
• Operating Supply Voltage: 3.75 V to 6 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: MCP73838T-FCI/MFTR

MCP73837/8
4.1
An internal undervoltage lockout (UVLO) circuit
monitors the input voltage and keeps the charger in
shutdown mode until the input supply rises above the
UVLO threshold. The UVLO circuitry has a built-in
hysteresis of 75 mV for the USB-Port and 55 mV for the
AC-Adapter.
In the event a battery is present when the input power
is applied, the input supply must rise 100 mV above the
battery
operational.
The UVLO circuit places the device in shutdown mode
if the input supply falls to within +100 mV of the battery
voltage.
The UVLO circuit is always active. At any time the input
supply is below the UVLO threshold or within +100 mV
of the voltage at the V
placed in a shutdown mode.
During any UVLO condition, the battery reverse
discharge current shall be less than 2 µA.
4.2
The MCP73837/8 devices are designed to select the
USB-port or the AC-Adapter as the power source
automatically. If the AC-Adapter input is not present,
the USB-Port is selected. If both inputs are available,
the AC-Adapter has first priority.
4.3
For a charge cycle to begin, all UVLO conditions must
be met and a battery or output load must be present.
A charge current programming resistor must be con-
nected from PROG1 to V
pin are open or floating, the MCP73837/8 is disabled
and the battery reverse discharge current is less than
2 µA. In this manner, the PROG1 pin acts as a charge
enable and can be used as a manual shutdown.
4.4
If the voltage at the V
preconditioning threshold, the MCP73837/8 enters a
preconditioning mode. The preconditioning threshold is
factory
Characteristics”
options.
DS22071A-page 16
Note:
Undervoltage Lockout (UVLO)
AUTONOMOUS POWER SOURCE
SELECTION
Charge Qualification
Preconditioning
set.
voltage
If the input power is switched during a
charge cycle, the power path switch-over
shall be a break-before-make connection.
As a result, the charge current can
momentarily go to zero. The charge cycle
timer shall remain continuous.
Refer
before
for
to
BAT
SS
preconditioning
BAT
. If the PROG1 or PROG2
Section 1.0
MCP73837/8
pin, the MCP73837/8 is
pin is less than the
“Electrical
threshold
becomes
In this mode, the MCP73837/8 supplies a percentage
of the charge current (established with the value of the
resistor connected to the PROG pin) to the battery. The
percentage or ratio of the current is factory set. Refer to
Section 1.0
preconditioning current options.
When the voltage at the V
preconditioning threshold, the MCP73837/8 enters the
constant current or fast charge mode.
4.5
During the constant current mode, the programmed
(AC-Adapter) or selected (USB-Port) charge current is
supplied to the battery or load.
For AC-Adapter, the charge current is established
using a single resistor from PROG to V
program resistor and the charge current are calculated
using the following equation:
EQUATION 4-1:
where R
milliampers (mA).
When
microcontroller has the option of selecting either a one
unit load or a five unit loads charge rate based on the
PROG2 input. A logic LOW selects a one unit load
charge rate, a HIGH selects a five unit loads charge
rate, and high impedance input suspends or disables
charging.
Constant current mode is maintained until the voltage
at the V
when constant current mode is invoked, the internal
timer is reset.
4.5.1
If the internal timer expires before the recharge voltage
threshold is reached, a timer fault is indicated and the
charge cycle terminates. The MCP73837/8 remains in
this condition until the battery is removed, the input
battery is removed or the PROG1/2 pin is opened. If the
battery is removed or the PROG1/2 pin is opened, the
MCP73837/8 enters the Stand-by mode where it
remains until a battery is reinserted or the PROG1/2 pin
Note:
BAT
charging
Constant Current MODE - Fast
Charge
PROG
USB Specification Rev. 2.0 defines the
maximum absolute current for one unit
load is 100 mA. This value is not an aver-
age over time and shall not be exceed.
TIMER EXPIRED DURING
CONSTANT CURRENT - FAST
CHARGE MODE
pin reaches the regulation voltage, V
“Electrical
is in kilo-ohms (kΩ) and I
I
from
REG
© 2007 Microchip Technology Inc.
=
a
---------------- -
R
1000V
BAT
PROG
Characteristics”
USB-Port,
pin rises above the
the
REG
SS
. The
REG
is in
host
for
.,