DS2710G+ Maxim Integrated Products, DS2710G+ Datasheet
DS2710G+
Specifications of DS2710G+
Related parts for DS2710G+
DS2710G+ Summary of contents
Page 1
... Monitors Voltage, Temperature, and Time for Safety and Secondary Termination Applications ♦ Regulates Charge Current ♦ Designed for External pMOS ♦ Rail-to-Rail MOSFET Driver ♦ Tiny 10-Pin TDFN Package (3mm x 4mm) DS2710G+ DS2710G+T&R + Denotes a lead(Pb)-free/RoHS-compliant package. T&R = Tape and reel Exposed pad. TOP VIEW ...
Page 2
Single-Cell NiMH Charger ABSOLUTE MAXIMUM RATINGS Voltage Range on All Pins Relative Continuous Source/Sink Current CS ...................................20mA Continuous Source Current STATUS ..................................10mA Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. ...
Page 3
DC ELECTRICAL CHARACTERISTICS (continued) (4.0V ≤ V ≤ 5.5V -20°C to +70°C, unless otherwise noted PARAMETER SYMBOL Cold Temperature Detect V THM-MIN Threshold Hot Temperature No-Start V THM-MAX Threshold Hot Temperature Safety V THM-STOP Shutdown Threshold ...
Page 4
Single-Cell NiMH Charger PIN NAME 1 V Device Ground. Connects directly to the negative terminal of the charge source Charge Source. Feedback control for switching circuitry. Power-Supply Input. Connects to the positive terminal of the charge source ...
Page 5
Detailed Description Charge Algorithm Overview The DS2710 controls switch-mode topology charging of a single NiMH cell from a voltage-regulated charge source. The IC is reset in one of two ways: with the application of power to the DS2710 or after ...
Page 6
Single-Cell NiMH Charger R > R TMR (ASYNCHRONOUSLY FROM ANYWHERE) V < UVLO UHYS (ASYNCHRONOUSLY FROM ANYWHERE) t < t PCHG AND V < 1.0V CELL V CELL T < +50°C t < FAST TIMEOUT t ...
Page 7
MAINTENANCE state any time during FAST- CHARGE the cell voltage exceeds V DS2710 determines that the cell is either overcharged or has been removed, and enters the FAULT state. CELL TEST is performed once every 31s during ...
Page 8
Single-Cell NiMH Charger Charge-Current Regulation The DS2710 regulates charge current by maintaining a constant average voltage across an external sense resistor connected between the VN1 and VN0 pins. VN1 and VN0 drive an internal comparator in the DS2710 to switch ...
Page 9
TOP-OFF complete normally if the cell temperature remains below this threshold. Used with a 10kΩ resistor, the Semitec 103AT-2 pro- vides approximately 0.9% full scale-per-degree sensi- tivity. Figure 4 shows this linearity curve. The left axis is the ratio of ...
Page 10
Single-Cell NiMH Charger Timeout Selection FAST-CHARGE state normally operates until -ΔV termi- nation. In the event that termination does not occur cor- rectly, a safety timeout is required. This timeout is set by an external resistor on the TMR pin ...
Page 11
R1 150Ω R4 10kΩ C1 1μF RT1 103AT-2 GROUND (USB-) Figure 5. Typical Application Circuit for USB Port Charging Referring to the example circuit and layout of Figure 6, the loop labeled as Loop1 encompassing ...
Page 12
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2008 Maxim Integrated Products ...