ICL7106CM44Z Intersil, ICL7106CM44Z Datasheet - Page 3

• Manufacturer Part Number: ICL7106CM44Z
• Description: IC ADC 3.5 DIGIT LCD/LED 44-MQFP
• Manufacturer: Intersil

Specifications of ICL7106CM44Z

• Display Type: LCD
• Configuration: 7 Segment
• Digits Or Characters: A/D 3.5 Digits
• Voltage - Supply: 4.75 V ~ 5.25 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 44-MQFP, 44-PQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Interface: -

Absolute Maximum Ratings
Supply Voltage
Analog Input Voltage (Either Input) (Note 1) . . . . . . . . . . . . V+ to V-
Reference Input Voltage (Either Input). . . . . . . . . . . . . . . . . V+ to V-
Clock Input
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
Electrical Specifications
SYSTEM PERFORMANCE
Zero Input Reading
Stability (Last Digit) (ICL7106S, ICL7107S
Only)
Ratiometric Reading
Rollover Error
Linearity
Common Mode Rejection Ratio
Noise
Leakage Current Input
Zero Reading Drift
Scale Factor Temperature Coefficient
End Power Supply Character V+ Supply
Current
End Power Supply Character V- Supply Current ICL7107 Only
COMMON Pin Analog Common Voltage
Temperature Coefficient of Analog Common
DISPLAY DRIVER ICL7106 ONLY
Peak-To-Peak Segment Drive Voltage
Peak-To-Peak Backplane Drive Voltage
1. Input voltages may exceed the supply voltages provided the input current is limited to ±100µA.
2. θ
ICL7106, V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15V
ICL7107, V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6V
ICL7107, V- to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -9V
ICL7106 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TEST to V+
ICL7107 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND to V+
JA
is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
PARAMETER
3
(Note 3)
V
25kΩ Between Common and
V
Fixed Input Voltage (Note 6)
V
-V
Difference in Reading for Equal Positive and Negative
Inputs Near Full Scale
Full Scale = 200mV or Full Scale = 2V Maximum
Deviation from Best Straight Line Fit (Note 5)
V
V
(Peak-To-Peak Value Not Exceeded 95% of Time)
V
V
(Ext. Ref. 0ppm/×
V
25kΩ Between Common and
Positive Supply (With Respect to + Supply)
Positive Supply (With Respect to + Supply)
V+ = to V- = 9V (Note 4)
ICL7106, ICL7107, ICL7107S
IN
IN
lN
CM
IN
lN
lN
IN
IN
= 0 (Does Not Include LED Current for ICL7107)
= 0.0V, Full Scale = 200mV
= V
= 0V, Full Scale = 200mV
= 0 (Note 5)
= 0, 0
= 199mV, 0
= +V
= 1V, V
o
REF
C to 70
lN
o
C To 70
, V
≅ 200mV
IN
REF
o
TEST CONDITIONS
= 0V, Full Scale = 200mV (Note 5)
o
C
C To 70
o
o
= 100mV
C) (Note 5)
C (Note 5)
o
C
,
Thermal Information
Thermal Resistance (Typical, Note 2)
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . .150
Maximum Storage Temperature Range . . . . . . . . . . -65
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300
NOTE: Pb-free PDIPs can be used for through hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MQFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(MQFP - Lead Tips Only)
-000.0
-000.0
MIN
999
2.4
4
-
-
-
-
-
-
-
-
-
-
±000.0
±000.0
999/10
TYP
±0.2
±0.2
0.2
1.0
0.6
3.0
5.5
00
50
15
80
1
1
+000.0
+000.0
MAX
1000
1.8
1.8
3.2
±1
±1
10
1
5
6
-
-
-
o
θ
C to 150
Reading
Reading
Reading
ppm/
ppm/
Counts
Counts
JA
Digital
Digital
Digital
µV/
UNIT
µV/V
mA
mA
µV
pA
V
V
FN3082.8
(
50
75
o
o
o
o
C
C/W)
C
C
o
o
o
C
C
C