MAX1494CCJ+ Maxim Integrated Products, MAX1494CCJ+ Datasheet - Page 10

IC ADC 4.5 DGT LCD DVR 32-TQFP

MAX1494CCJ+

Manufacturer Part Number
MAX1494CCJ+
Description
IC ADC 4.5 DGT LCD DVR 32-TQFP
Manufacturer
Maxim Integrated Products
Datasheet

Specifications of MAX1494CCJ+

Display Type
LCD
Configuration
7 Segment + 2 Annunciators
Interface
Serial
Digits Or Characters
A/D 4.5 Digits
Current - Supply
960µA
Voltage - Supply
2.7 V ~ 5.25 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
32-LQFP
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
0 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
The MAX1492/MAX1494 low-power, highly integrated
ADCs with LCD drivers convert a ±2V differential input
voltage (one count is equal to 100µV for the MAX1494
and 1mV for the MAX1492) with a sigma-delta ADC and
output the result to an LCD or µC. An additional
±200mV input range (one count is equal to 10µV for the
MAX1494 and 100µV for the MAX1492) is available to
measure small signals with increased resolution.
The devices operate from a single 2.7V to 5.25V power
supply and offer 3.5-digit (MAX1492) or 4.5-digit
(MAX1494) conversion results. An internal 2.048V refer-
ence, an internal charge pump, and a high-accuracy
on-chip oscillator eliminate external components.
The MAX1492 and MAX1494 interface with a µC using
an SPI/QSPI/MICROWIRE-compatible serial interface.
Data can either be sent directly to the display or to the
µC first for processing before being displayed.
The devices also feature on-chip buffers for the differen-
tial input signal and external reference inputs, allowing
direct interface with high-impedance signal sources. In
addition, they use continuous internal-offset calibration
and offer >100dB of 50Hz and 60Hz line noise rejec-
tion. Other features include data hold and peak hold,
overrange and underrange detection, and a low-battery
monitor.
Internal protection diodes limit the analog input range
from V
exceeds this range, limit the input current to 10mA.
The MAX1492/MAX1494 analog input/reference buffers
allow the use of high-impedance signal sources. The
input buffer’s common-mode input range allows the ana-
log inputs and the reference to range from -2.2V to +2.2V.
The MAX1492/MAX1494 perform analog-to-digital con-
versions using a single-bit, 3rd-order, sigma-delta mod-
ulator. The sigma-delta modulator converts the input
signal into a digital pulse train whose average duty
cycle represents the digitized signal information. The
modulator quantizes the input signal at a much higher
sample rate than the bandwidth of the input.
The MAX1492/MAX1494 modulator provides 3rd-order
frequency shaping of the quantization noise resulting
from the single-bit quantizer. The modulator is fully dif-
ferential for maximum signal-to-noise ratio and mini-
mum susceptibility to power-supply noise. A single-bit
data stream is then presented to the digital filter to
remove the frequency-shaped quantization noise.
3.5- and 4.5-Digit, Single-Chip ADCs
with LCD Drivers
10
Internal Analog Input/Reference Buffers
___________________________________________________________________________________________________
NEG
to (V
AVDD
Detailed Description
Analog Input Protection
+ 0.3V). If the analog input
Modulator
The MAX1492/MAX1494 contain an on-chip digital low-
pass filter that processes the data stream from the
modulator using a SINC
SINC
ods (4 x 200ms).
The MAX1492/MAX1494 have 25% overrange capability
built into the modulator and digital filter.
The digital filter is optimized for f
Lower clock frequencies can be used; however,
50Hz/60Hz noise rejection decreases. The frequency
response of the SINC
where N is the oversampling ratio, and fm = N
data rate = 5Hz.
Figure 2 shows the filter frequency response. The
SINC
times the first-notch frequency (5Hz).
The output data rate for the digital filter corresponds
with the positioning of the first notch of the filter’s fre-
quency response. The notches of the SINC
repeated at multiples of the first-notch frequency. The
SINC
100dB at these notches. For example, 50Hz is equal to
Figure 2. Frequency Response of the SINC
4
4
4
filter has a settling time of four output data peri-
characteristic -3dB cutoff frequency is 0.228
filter provides an attenuation of better than
-120
-160
-200
-40
-80
0
H z
H f
0
( )
( )
=
10
=
4
N
1 1
filter is measured as follows:
N
1
20
(
(
sin
FREQUENCY (Hz)
1
sin
4
z
z
N
((sinx/x)
30
π
N
π
1
fm
)
)
CLK
fm
f
f
4
40
Filter Characteristics
Digital Filtering
equal to 4.9152MHz.
4
4
4
Filter (Notch at 60Hz)
50
) response. The
60
4
filter are

output

Related parts for MAX1494CCJ+