ZXLD1350ET5TA Diodes Zetex, ZXLD1350ET5TA Datasheet
ZXLD1350ET5TA
Specifications of ZXLD1350ET5TA
Available stocks
Related parts for ZXLD1350ET5TA
ZXLD1350ET5TA Summary of contents
Page 1
Description The ZXLD1350 is a hysteretic mode inductive step-down converter with integrated switch and high side current sense. It operates from an input supply from 7V to 30V driving single or multiple series connected LEDs efficiently external adjustable output current ...
Page 2
Block Diagram ADJ Vref GND Pin Description Name Pin No Drain of NDMOS switch GND 2 Ground (0V) Multi-function On/Off and brightness control pin: • Leave floating for normal operation.(V I =0.1/R OUTnom • Drive ...
Page 3
Absolute Maximum Ratings Symbol Parameter V Input Voltage Voltage SENSE SENSE V LX Output Voltage LX V Adjust Pin Input Voltage ADJ I Switch Output Current LX Power Dissipation P (Refer to Package thermal de-rating curve on ...
Page 4
Electrical Characteristics Symbol Parameter V Internal regulator start-up threshold SU I Quiescent supply current with output off INQoff I Quiescent supply current with output switching INQon Mean current sense threshold voltage V SENSE (Defines LED current setting accuracy) V Sense ...
Page 5
Device Description The device, in conjunction with the coil (L1) and current sense resistor (R converter. Device operation (Refer to block diagram and Figure 1 - Operating waveforms) Operation can be best understood by assuming that the ADJ pin of ...
Page 6
Device Description (Continued) ZXLD1350 Document number: DS33468 Rev 30V 350mA LED DRIVER with AEC-Q100 Figure 1. Theoretical Operating Waveforms www.diodes.com A Product Line of Diodes Incorporated ZXLD1350 March 2011 © Diodes Incorporated ...
Page 7
Device Description (Continued) Typical Operating Waveforms [V Normal operation. Output current (Ch3) and LX voltage (Ch1) Start-up waveforms. Output current (Ch3), LX voltage (Ch1) and V ZXLD1350 Document number: DS33468 Rev 30V 350mA LED DRIVER with AEC-Q100 ...
Page 8
Typical Operating Conditions ZXLD1350 Document number: DS33468 Rev Product Line of Diodes Incorporated 30V 350mA LED DRIVER with AEC-Q100 www.diodes.com ZXLD1350 March 2011 © Diodes Incorporated ...
Page 9
Typical Characteristics (Continued) ZXLD1350 Document number: DS33468 Rev Product Line of Diodes Incorporated 30V 350mA LED DRIVER with AEC-Q100 www.diodes.com ZXLD1350 March 2011 © Diodes Incorporated ...
Page 10
Typical Characteristics (Continued) ZXLD1350 Document number: DS33468 Rev Product Line of Diodes Incorporated 30V 350mA LED DRIVER with AEC-Q100 www.diodes.com ZXLD1350 March 2011 © Diodes Incorporated ...
Page 11
Typical Characteristics (Continued) ZXLD1350 Document number: DS33468 Rev Product Line of Diodes Incorporated 30V 350mA LED DRIVER with AEC-Q100 www.diodes.com ZXLD1350 March 2011 © Diodes Incorporated ...
Page 12
Application Information Setting nominal average output current with external resistor R The nominal average output current in the LED(s) is determined by the value of the external current sense resistor (R connected between V and I and is given by: ...
Page 13
Application Information (Continued) Output Current Adjustment by PWM Control Directly driving ADJ input A Pulse Width Modulated (PWM) signal with duty cycle D output current to a value above or below the nominal average value set by resistor R PWM ...
Page 14
Application Information (Continued) Low frequency PWM mode When the ADJ pin is driven with a low frequency PWM signal (eg 100Hz), with a high level voltage V zero, the output of the internal low pass filter will swing between 0V ...
Page 15
Application Information (Continued) High frequency PWM mode At PWM frequencies above 10kHz and for duty cycles above 0.16, the output of the internal low pass filter will contain a DC component that is always above the shutdown threshold. This will ...
Page 16
Application Information (Continued) Soft-start The device has inbuilt soft-start action due to the delay through the PWM filter. An external capacitor from the ADJ pin to ground will provide additional soft-start delay, by increasing the time taken for the voltage ...
Page 17
Application Information (Continued) Inductor Selection Recommended inductor values for the ZXLD1350 are in the range 47µH to 220µH. Higher values of inductance are recommended at higher supply voltages in order to minimize errors due to switching delays, which result in ...
Page 18
Application Information (Continued) Example: For V =12V, L=47µH, rL=0.64V LED t = (47e-6 x 0.105)/(12 - 3.4 - 0.672) = 0.622µ (47e-6 x 0.105)/(3.4 + 0.36 + 0.322)= 1.21µs OFF This gives an operating frequency ...
Page 19
Application Information (Continued) A value of 1μF will reduce nominal ripple current by a factor three (approx.). Proportionally lower ripple can be achieved with higher capacitor values. Note that the capacitor will not affect operating frequency or efficiency, but it ...
Page 20
Application Information (Continued) Layout considerations LX pin The LX pin of the device is a fast switching node, so PCB tracks should be kept as short as possible. To minimize ground 'bounce', the ground pin of the device should be ...
Page 21
... Ordering Information Part Package Device Code Mark ZXLD1350ET5TA 1350 ET5 Note: 5. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf. Package Outline Dimensions TSOT23 ZXLD1350 Document number: DS33468 Rev Diodes Incorporated 30V 350mA LED DRIVER with AEC-Q100 ...
Page 22
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY ...