L6585D STMicroelectronics, L6585D Datasheet - Page 6

• Manufacturer Part Number: L6585D
• Description: IC CTRLR PFC/BALLAST SOIC-20
• Manufacturer: STMicroelectronics
• Type: PFC/Ballast Controllerr

Specifications of L6585D

• Frequency: 58.4 ~ 62 kHz
• Current - Supply: 7mA
• Current - Output: 600mA
• Voltage - Supply: 11 V ~ 16 V
• Operating Temperature: -40°C ~ 150°C
• Package / Case: 20-SOIC (7.5mm Width)
• For Use With: 497-8421 - BOARD DEMO 1X54W T5 LAMP497-8405 - BOARD EVAL L6585D/TSM101
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Pin settings
6/25
Table 1.
Pin num. Name
10
11
12
13
14
15
16
17
18
19
20
9
COMP
HBCS
BOOT
PFCS
GND
ZCD
PFG
VCC
OUT
HSD
LSD
Pin functions (continued)
INV
Output of the error amplifier. A compensation network is placed between this pin
and INV to achieve stability of the PFC voltage control loop and ensure high
power factor and low THD.
Inverting input of the error amplifier. The information on the output voltage of the
PFC pre-regulator is fed into the pin through a resistor divider. Input for the
feedback disconnection comparator
Boost inductor’s demagnetization sensing input for PFC transition-mode
operation. A negative-going edge triggers PFC MOSFET turn-on.
During start-up or when the voltage is not high enough to arm the internal
comparator (e.g. AC Mains peak), the PFC driver is triggered by means of an
internal starter.
Input to the PFC PWM comparator. The current flowing in the PFC mosfet is
sensed by a resistor; the resulting voltage is applied to this pin and compared
with an internal sinusoidal-shaped reference, generated by the multiplier, to
determine the PFC MOSFET’ s turn-off.
A second comparison level detects abnormal currents (e.g. due to boost inductor
saturation) and, on this occurrence, shuts down and latches the IC reducing its
consumption to the start-up.
An internal LEB prevents undesired function triggering.
PFC gate driver output. The totem pole output stage is able to drive power
MOSFET’S with a peak current of 300mA source and 600mA sink.
2-levels half-bridge current monitor for current control.
The current flowing in the HB mosfet is sensed by a resistor; the resulting
voltage is applied to this pin.
Low threshold (active during run mode): in case of thresholds crossing, the IC
reacts with self-adjusting frequency increase in order to limit the half-bridge
(lamp) current.
High threshold:
– ignition: in case of thresholds crossing during the frequency shift, the IC reacts
– run mode: in case of thresholds crossing because of current spikes (due e. g.
Ground. Current return for both the signal part of the IC and the gate driver.
Low side driver output: the output stage can deliver 290mA source and 480mA
sink (typ. values).
Supply Voltage of both the signal part of the IC and the gate driver.
Clamped with a Zener inside.
High Side Driver Floating Reference. This pin must be connected close to the
source of the high side power MOS.
High side driver output: the output stage can deliver 290mA source and 480mA
(typ. values).
Bootstrapped Supply Voltage. Between this pin and V
must be connected.
A patented integrated circuitry replaces the external bootstrap diode, by means
of a high voltage DMOS, synchronously driven with the low side power MOSFET.
with self-adjusting frequency increase in order to limit the lamp voltage and
preventing operation below resonance.
to capacitive mode / cross-conduction), the L6585D latches to avoid
MOSFETs damaging,
Function
CC
, the bootstrap capacitor
L6585D