TC4467CPD Microchip Technology, TC4467CPD Datasheet - Page 9

• Manufacturer Part Number: TC4467CPD
• Description: IC MOSFET DVR QUAD NAND 14DIP
• Manufacturer: Microchip Technology
• Type: Microcontrollerr

Specifications of TC4467CPD

• Number Of Outputs: 4
• Package / Case: 14-DIP (0.300", 7.62mm)
• Configuration: Low-Side
• Input Type: NAND
• Delay Time: 40ns
• Current - Peak: 1.2A
• Number Of Configurations: 4
• Voltage - Supply: 4.5 V ~ 18 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Rise Time: 25 ns
• Fall Time: 25 ns
• Supply Voltage (min): 4.5 V
• Supply Current: 4 mA
• Maximum Power Dissipation: 800 mW
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: 0 C
• Number Of Drivers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• High Side Voltage - Max (bootstrap): -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 158-1118; 158-1118

4.0
4.1
Large currents are required to charge and discharge
large capacitive loads quickly. For example, charging a
1000 pF load to 18 V in 25 nsec requires 0.72 A from
the device's power supply.
To ensure low supply impedance over a wide frequency
range, a 1 µF film capacitor in parallel with one or two
low-inductance, 0.1 µF ceramic disk capacitors with
short lead lengths (<0.5 in.) normally provide adequate
bypassing.
4.2
The TC4467 and TC4469 contain inverting drivers.
Potential
impedances from input to output will appear as
negative feedback and degrade switching speed
characteristics. Instead, individual ground returns for
input and output circuits, or a ground plane, should be
used.
4.3
The input voltage level changes the no-load or
quiescent supply current. The N-channel MOSFET
input stage transistor drives a 2.5 mA current source
load. With logic “0” outputs, maximum quiescent supply
current is 4 mA. Logic “1” output level signals reduce
quiescent current to 1.4 mA, maximum. Unused driver
inputs must be connected to V
power dissipation occurs for logic “1” outputs.
The drivers are designed with 50 mV of hysteresis,
which provides clean transitions and minimizes output
stage current spiking when changing states. Input volt-
age thresholds are approximately 1.5 V, making any
voltage greater than 1.5 V, up to V
Input current is less than 1 µA over this range.
2002 Microchip Technology Inc.
Supply Bypassing
Grounding
Input Stage
DETAILED DESCRIPTION
drops
developed
in
DD
DD
common
or V
, a logic “1” input.
SS
. Minimum
ground
TC4467/TC4468/TC4469
4.4
The supply current versus frequency and supply
current versus capacitive load characteristic curves will
aid in determining power dissipation calculations.
Microchip Technology's CMOS drivers have greatly
reduced quiescent DC power consumption.
Input signal duty cycle, power supply voltage and load
type influence package power dissipation. Given power
dissipation and package thermal resistance, the maxi-
mum
calculated. The 14-pin plastic package junction-to-
ambient thermal resistance is 83.3°C/W. At +70°C, the
package is rated at 800 mW maximum dissipation.
Maximum allowable chip temperature is +150°C.
Three components make up total package power
dissipation:
1.
2.
3.
A capacitive-load-caused dissipation (driving MOSFET
gates), is a direct function of frequency, capacitive load
and supply voltage. The power dissipation is:
EQUATION
A
referenced loads is a function of duty cycle, load
current and load voltage. The power dissipation is:
EQUATION
resistive-load-caused
Load-caused dissipation (P
Quiescent power (P
Transition power (P
f
C
V
D
V
V
I
L
S
=
S
L
ambient
=
=
=
=
Power Dissipation
=
=
Switching Frequency
Capacitive Load
Duty Cycle
Supply Voltage
Load Current
Supply Voltage
Load Voltage
P
L
operating
=
P
L
D V
=
T
Q
).
).
fCV
S
–
dissipation
V
temperature
2
S
L
L
).
I
L
DS21425B-page 9
for
is
ground-
easily