MIC4452YM Micrel Inc, MIC4452YM Datasheet - Page 10

• Manufacturer Part Number: MIC4452YM
• Description: IC DRIVER MOSFET 12A HS 8-SOIC
• Manufacturer: Micrel Inc

Specifications of MIC4452YM

• Configuration: Low-Side
• Input Type: Non-Inverting
• Delay Time: 15ns
• Current - Peak: 12A
• Number Of Configurations: 1
• Number Of Outputs: 1
• Voltage - Supply: 4.5 V ~ 18 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Device Type: Low Side
• Module Configuration: Low Side
• Peak Output Current: 12A
• Output Resistance: 0.8ohm
• Input Delay: 15ns
• Output Delay: 35ns
• Supply Voltage Range: 4.5V To 18V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• High Side Voltage - Max (bootstrap): -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 576-1530-5; MIC4452YM

Resistive Load Power Dissipation
Dissipation caused by a resistive load can be calculated
as:
where:
I = the current drawn by the load
R
is high, at the power supply voltage used. (See data
sheet)
D = fraction of time the load is conducting (duty cycle)
Capacitive Load Power Dissipation
Dissipation caused by a capacitive load is simply the
energy placed in, or removed from, the load capacitance
by the driver. The energy stored in a capacitor is
described by the equation:
As this energy is lost in the driver each time the load is
charged or discharged, for power dissipation calculations
the 1/2 is removed. This equation also shows that it is
good practice not to place more voltage on the capacitor
than is necessary, as dissipation increases as the
square of the voltage applied to the capacitor. For a
driver with a capacitive load:
where:
f = Operating Frequency
C = Load Capacitance
V
Micrel Inc.
January 2011
S
O
= Driver Supply Voltage
= the output resistance of the driver when the output
Table 1: MIC4451 Maximum Operating Frequency
P
E = 1/2 C V
P
L
L
= I
= f C (V
18V
15V
10V
VS
5V
2
R
O
D
S
2
)
2
Max. Frequency
220kHz
300kHz
640kHz
2MHz
10
Inductive Load Power Dissipation
For inductive loads the situation is more complicated.
For the part of the cycle in which the driver is actively
forcing current into the inductor, the situation is the same
as it is in the resistive case:
However, in this instance the R
the on resistance of the driver when its output is in the
high state, or its on resistance when the driver is in the
low state, depending on how the inductor is connected,
and this is still only half the story. For the part of the
cycle when the inductor is forcing current through the
driver, dissipation is best described as:
where V
driver (generally around 0.7V). The two parts of the load
dissipation must be summed in to produce P
Quiescent Power Dissipation
Quiescent power dissipation (P
input section) depends on whether the input is high or
low. A low input will result in a maximum current drain
(per driver) of ≤ 0.2mA; a logic high will result in a
current drain of ≤ 3.0mA. Quiescent power can therefore
be found from:
where:
I
I
D = fraction of time input is high (duty cycle)
V
H
L
S
= quiescent current with input low
= quiescent current with input high
= power supply voltage
P
P
P
P
D
L1
L2
L
Q
is the forward drop of the clamp diode in the
= P
= V
= I
= I V
2
L1
S
R
[D I
D
+ P
O
(1 – D)
D
H
L2
+ (1 – D) I
L
O
]
Q
required may be either
, as described in the
MIC4451/4452
M9999-011811
L
: