LT1166CS8 Linear Technology, LT1166CS8 Datasheet
LT1166CS8
Specifications of LT1166CS8
Available stocks
Related parts for LT1166CS8
LT1166CS8 Summary of contents
Page 1
... The LT1166 can be biased from a pair of resistors or current sources and because it operates on the drive voltage to the output transistors, it operates on any supply voltage. , LTC and LT are registered trademarks of Linear Technology Corporation. 15V + 220 F R2 ...
Page 2
... Industrial grade parts specified and tested over – and 85 C are available on special request, consult factory. Note 3: T calculated from the ambient temperature T J dissipation P according to the following formulas: D LT1166CN8 • 100 C/ LT1166CS8 • 150 C/ Note TOP BOTTOM 2 U RATINGS PACKAGE/ORDER ...
Page 3
W U TYPICAL PERFORMANCE CHARACTERISTICS Input Bias Current vs Current Source Mismatch 150 100 50mA TOP BOTTOM 4mA TOP BOTTOM –50 –100 –150 –10 –7.5 –5.0 –2.5 0 2.5 5.0 ...
Page 4
LT1166 W U TYPICAL PERFORMANCE CHARACTERISTICS Input Transconductance vs Supply Voltage 0.120 25 C 0.110 0.100 125 C – 0.090 0.080 V = 200mV –0.080 –0.090 125 ...
Page 5
U U APPLICATIONS INFORMATION Overvoltage Protection The supplies V (Pin 1) and V TOP BOTTOM diodes that turn on when they exceed 12V. These diodes act as ESD protection and serve to protect the LT1166 when used with large power ...
Page 6
LT1166 APPLICATIONS INFORMATION Similarly for V , when positive voltage is applied current that was flowing in R1 and Q1 is now supplied IN through R . This effect ...
Page 7
U U APPLICATIONS INFORMATION how tapping the sense resistors gives twice the limit current or one half the limit current. Foldback current limit can be added to the normal or “square” current limit by including two resistors (30k typical) from ...
Page 8
LT1166 APPLICATIONS INFORMATION APPLICATION CIRCUITS Bipolar Buffer Similar to the unity gain buffer in Figure 1, the LT1166 can be used to bias bipolar transistors as shown in Figure 8. The minimum operating voltage for the LT1166 ...
Page 9
U U APPLICATIONS INFORMATION Adding Voltage Gain The circuit in Figure 9 adds voltage gain to the circuit in Figure 1. At low frequency the LT1166 is in the feedback INPUT OUTPUT Figure 10. Power Amp Driving ...
Page 10
... W U common mode voltage to its output. The following appli- cations utilize amplifiers operating in suspended-supply operation (Figure 13). See “Linear Technology Magazine” Volume IV Number 2 for a discussion of suspended supplies. The gain setting resistors used in suspended- supply operation must be tight tolerance or the gain will be wrong ...
Page 11
U U APPLICATIONS INFORMATION Parallel Operation Parallel operation is an effective way to get more output power by connecting multiple power drivers. All that is required is a small ballast resistor to ensure current sharing between the drivers and an ...
Page 12
LT1166 U U APPLICATIONS INFORMATION Figure 15. 0.3% THD at 10kHz Figure 16. Clipping at 1kHz, R 100W Audio Power Amplifier The details of a low distortion audio amplifier are shown in Figure 19. The LT1360, designated U1, ...
Page 13
U U APPLICATIONS INFORMATION W U LT1166 13 ...
Page 14
LT1166 APPLICATIONS INFORMATION 8kHz Figure 20. Square Wave Response Into 1166 • F20 20kHz Figure 21. 100W 20kHz Sine Wave and Its ...
Page 15
... MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 16
... Current Feedback Amplifier LT1210 1A/40MHz Current Feedback Amplifier LT1270A 10A High Efficiency Switching Regulator LT1360 50MHz, 800V Amp LT1363 70MHz, 800V Amp C-Load is a registered trademark of Linear Technology Linear Technology Corporation 16 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 : (408) 434-0507 FAX TELEX U Dimensions in inches (millimeters) unless otherwise noted ...