IR22141SS International Rectifier, IR22141SS Datasheet

no-image

IR22141SS

Manufacturer Part Number
IR22141SS
Description
IC DRIVER HALF BRIDGE SGL 24SSOP
Manufacturer
International Rectifier
Datasheet

Specifications of IR22141SS

Configuration
Half Bridge
Input Type
Non-Inverting
Delay Time
440ns
Current - Peak
2A
Number Of Configurations
1
Number Of Outputs
2
High Side Voltage - Max (bootstrap)
1200V
Voltage - Supply
11.5 V ~ 20 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
24-SSOP
Family Hvic
General Purpose HVICs
Channels
2
Topology
Half Bridge
Application
General Purpose / Motor Control
Voffset
1200
Io+ (ma)
2000
Io- (ma)
3000
Separate Power And Logic Ground
Yes
Uvlo
Vcc / Vbs
Vbsuv+ / Vccuv+ Min (v)
9.3
Vbsuv+ / Vccuv+ Typ (v)
10.2
Vbsuv+ / Vccuv+ Max (v)
11.4
Vbsuv- / Vccuv- Min (v)
8.7
Vbsuv- / Vccuv- Typ (v)
9.3
Vbsuv- / Vccuv- Max (v)
10.3
Dt / Sdt Min (ns)
5700
Dt / Sdt Typ (ns)
9250
Dt / Sdt Max (ns)
13500
T On Min (ns)
220
T On Typ (ns)
440
T On Max (ns)
660
T Off Min (ns)
220
T Off Typ (ns)
440
T Off Max (ns)
660
Fault Reporting
Yes
Package
24 Lead
Part Status
Active & Preferred
Special Features
Soft Shutdown and Desaturation Detection
For Use With
IRMD2214SS - KIT DESIGN EVAL BOARD IR2214SSIRMD22141SS - KIT DESIGN EVAL BOARD/IR22141SS
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
*IR22141SS

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
IR22141SS
Manufacturer:
IR
Quantity:
20 000
Part Number:
IR22141SSPBF
Manufacturer:
International Rectifier
Quantity:
135
Part Number:
IR22141SSPBF
Manufacturer:
IR
Quantity:
20 000
Part Number:
IR22141SSTRPBF
Manufacturer:
IR
Quantity:
20 000
www.irf.com
Features
Description
The IR21141/IR22141 gate driver family is suited to drive a single half bridge
in power switching applications. These drivers provide high gate driving
capability (2 A source, 3 A sink) and require low quiescent current, which
allows the use of bootstrap power supply techniques in medium power
systems. These drivers feature full short circuit protection by means of power
transistor desaturation detection and manage all half-bridge faults by
smoothly turning off the desaturated transistor through the dedicated soft
shutdown
electromagnetic emissions. In multi-phase systems, the IR21141/IR22141
drivers communicate using a dedicated local network (SY_FLT and
FAULT/SD signals) to properly manage phase-to-phase short circuits. The
system controller may force shutdown or read device fault state through the
3.3 V compatible CMOS I/O pin (FAULT/SD). To improve the signal immunity
from DC-bus noise, the control and power ground use dedicated pins
enabling low-side emitter current sensing as well. Undervoltage conditions in
floating and low voltage circuits are managed independently.
Typical connection
Floating channel up to 600 V or 1200 V
Soft over-current shutdown
Synchronization signal to synchronize shutdown with the other phases
Integrated desaturation detection circuit
Two stage turn on output for di/dt control
Separate pull-up/pull-down output drive pins
Matched delay outputs
Undervoltage lockout with hysteresis band
Lead free
pin,
therefore
preventing
over-voltages
14-Aug-09
1
HALF-BRIDGE GATE DRIVER IC
and
reducing
IR21141SSPbF/IR22141SSPbF
Product Summary
Package
Deadtime matching (max)
Desat blanking time (typ)
Soft shutdown time (typ)
DSH, DSL input voltage
Deadtime (typ)
threshold (typ)
I
O
Data Sheet No. PD60349 revL
V
+/- (min)
OFFSET
V
24-Lead SSOP
OUT
© 2009 International Rectifier
10.4 V – 20 V
1200 V max.
1.0 A / 1.5 A
600 V or
9.25 µs
330
75 ns
8.0 V
3
µs
ns

Related parts for IR22141SS

IR22141SS Summary of contents

Page 1

... DC-bus noise, the control and power ground use dedicated pins enabling low-side emitter current sensing as well. Undervoltage conditions in floating and low voltage circuits are managed independently. Typical connection www.irf.com IR21141SSPbF/IR22141SSPbF HALF-BRIDGE GATE DRIVER IC Product Summary Deadtime matching (max) Desat blanking time (typ) ...

Page 2

... The thermal resistance SS Definition IR21141 IR22141 ≤ 25 ° Definition † IR21141 †† IR22141 from +600 V or 1200 V. Logic state held for (referenced less than 200ns the IC will withstand a sustained peak IR21141/IR22141SSPbF Min. Max. Units 0 -0.3 625 -0.3 1225 -0.3 25 ...

Page 3

... DESAT DS Min Typ Max Units 7.2 8.0 8.8 V 6.3 7.0 7.7 — 1.0 — — 21 — µA — -160 — — -20 — IR21141/IR22141SSPbF Min Typ Max Units Test Conditions 9.3 10.2 11.4 8.7 9.3 10.3 — 0.9 — V 9.3 10.2 11.4 ...

Page 4

... Soft Shutdown on resistance ON,SSD I Output low short circuit pulsed current O- † SSD operation only www.irf.com Definition – –V B HOP CC LOP Definition or V HON LON † 4 IR21141/IR22141SSPbF Min Typ Max Units Test Conditions — 40 300 HOP/LOP PW≤ — 200 ns, resistive load, see Fig. 8 ...

Page 5

... IR21141/IR22141SSPbF Max. Units Test Conditions 660 & 600 660 or 1200 V, HOP shorted to HON, LOP — shorted to LON, Fig — 280 Fig. 8 4600 ...

Page 6

... DSL/DSH V DESAT COM on/off internal signal LOP/HOP desat internal signal Figure 6: HON, LON, SSDH and SSDL Diagram 6 IR21141/IR22141SSPbF schm itt trigger internal signal 10k 100k active bias comparator internal SSD signal 700k Figure 4: DSH and DSL Diagram LON/HON SSDL/SSDH V OL ...

Page 7

... HIN LIN (HOP=HON) LO (LOP=LON) HIN/LIN DSH/DSL SSD Driver Enable HO/LO www.irf.com 50% 50 out 90% 10% Figure 7: Switching Time Waveforms Ton1 Io1+ Io2+ Figure 8: Output Source Current DESAT Figure 9: Soft Shutdown Timing Waveform 7 IR21141/IR22141SSPbF 3.3V t off t f 90% 10% 3.3V © 2009 International Rectifier ...

Page 8

... HIN HO (HOP=HON) LO (LOP=LON) 50% www.irf.com 50 50% 50% t SY_FLT,DESAT3 DESAT2 90% SoftShutdown t DESAT3 90% SoftShutdown 50% 10 Turn-On Propagation Delay Figure 10: Desat Timing 50% 50% DTH MDT=DTH-DTL Figure 11: Internal Deadtime Timing 8 IR21141/IR22141SSPbF 50% 8V 50% t SY_FLT,DESAT4 Turn_Off propagation Delay 90% t DESAT4 90% SoftShutdown 50% 90 50% DTL 50% © 2009 International Rectifier ...

Page 9

... HOP High side driver sourcing output HON High side driver sinking output DSH High side IGBT desaturation protection input SSDH High side soft shutdown V High side floating supply return S www.irf.com IR21141/IR22141SSPbF 1 HIN LIN FLT_CLR SY_FLT FAULT/SD VSS SSOP24 SSDL COM LON ...

Page 10

... HO=0, LO=LIN UV_VCC HO/LO=1 UV_VBS Freeze STATE DIAGRAM Temporary State SOFT SHUTDOWN − START UP SEQUENCE − state, the HO goes high only if a rising edge event happens IR21141/IR22141SSPbF VB on/off HOP LATCH di/dt control Driver LOCAL DESAT soft HON PROTECTION shutdown SSDH UV_VBS DETECT ...

Page 11

... INPUT/OUTPUT ______ _________ SY_FLT FAULT/SD SSD: desat (out) SD: shutdown (in) HOLD: freezing FAULT: diagnostic (in) (out (SD) (FAULT) † (SSD (SSD (SSD) (FAULT) 0 (SSD) (FAULT (HOLD (FAULT) 11 IR21141/IR22141SSPbF SSDH/SSDL HiZ HiZ 0 Undervoltage Yes: V< UV threshold No : V> UV OUTPUTS threshold X: don’t care †† SSD ...

Page 12

... IR21141/IR22141SSPbF 1.4 Fault Management The IR21141/IR22141 is able to manage supply failure (undervoltage lockout) and transistor desaturation (on both the low and high side switches). ...

Page 13

... BL 1.4.4 Fault Management in Multi-Phase Systems In a system with two or more gate drivers the IR21141/IR22141 devices must be connected as shown in Fig. 15. 13 IR21141/IR22141SSPbF DesatHS DesatLS UVCC ). Once SS © 2009 International Rectifier ...

Page 14

... Fig. 16. In certain switching conditions (short pulses, high temperature) the recovery current of the external de- saturation sensing diode might reach levels beyond the capability of the active bias circuit. In order to avoid malfunctions and damage for the IC an external Schottky 14 IR21141/IR22141SSPbF When the and a pull- ...

Page 15

... Timing and Logic State Diagrams Description The following figures show the input/output logic diagram. Figure 17 shows the SY_FLT and FAULT/SD signals as outputs, whereas Fig. 18 shows them as inputs HIN LIN 15 IR21141/IR22141SSPbF ). This feature boosts the total on1 ) and © 2009 International Rectifier ...

Page 16

... FLT_CLR (see FAULT/SD section), D. The FAULT/SD is released and the outputs go back to follow the inputs, E. Externally driven low FAULT/SD: outputs go off by hard shutdown (like point B point A and B but for the low side output IR21141/IR22141SSPbF © 2009 International Rectifier ...

Page 17

... ESR ceramic may result in an efficient solution). Then we have: DC TOT + V GE The minimum size of bootstrap capacitor is: I LOAD motor V CEon example follows using IR2214SS or IR22141SS: COM a) using 125 ° C 1200 V IGBT (IRGP30B120KD): • 800 µA QBS • µA LK • 160 nC • Q drastically these G • I LK_GE • ...

Page 18

... Q IGBT gate). To obtain the desired switching time the gate resistance can be sized starting from Vcc , and voltage drop BS R < 100 ns IR21141/IR22141SSPbF supply. CC and R ). DRn * indicates the plateau ge and Q indicate the gate to collector and ...

Page 19

... V > must be verified to avoid spurious turn on. Rearranging the equation yields: to avoid BL is Goff R is approximately given by DRn RESoff 19 IR21141/IR22141SSPbF and R (see Fig. 22). If the voltage Goff DRn dV/dt HS Turning ON C RESoff R Goff OFF R C DRn IES Sizing: Current Path When Low Side is ...

Page 20

... Driven R Sizing OUT Gon Vth(min) CRESoff Table 3: R Sizing Goff 20 IR21141/IR22141SSPbF (calculated with the Goff / V/ns . out RGon → std commercial value RTOT - RDRp = 12.7 → 10 → 420 ns RTOT - RDRp = 32.5 → 33 → 202 ns RGon → std commercial value dVout/dt RTOT - RDRp = 6.5 → ...

Page 21

... parasitic Information below refers to Fig. 24: Bootstrap section: R1, C1, D1 High side gate: R2, R3, R4 High side Desat: D2 Low side supply: C2 Low side gate: R5, R6, R7 Low side Desat IR21141/IR22141SSPbF . DC IR2214 D3 Phase Top Layer Bottom Layer c) Ground Plane Figure 24: layout example © 2009 International Rectifier ...

Page 22

... Figures 25-83 provide information on the experimental performance of the IR21141/IR22141SSPbF HVIC. The line plotted in each figure is generated from actual lab data. A large number of individual samples from multiple wafer lots were tested at three temperatures (-40 ºC, 25 ºC, and 125 ºC) in order to generate the experimental (Exp.) curve. The line labeled Exp ...

Page 23

... C) Figure 32. V 2.20 1.90 Exp. 1.60 1.30 1.00 -50 75 100 125 C) Figure 34. LIN Logic "1" Input Voltage vs. Temperature 0.90 0.70 Exp. 0.50 0.30 0.10 75 100 125 - Figure 36 IR21141/IR22141SSPbF - 100 o Temperature ( C) Logic Input Voltage vs. Temperature IL - 100 o Temperature ( C) - 100 o Temperature ( C) LIN Logic Input Hysteresis vs. ...

Page 24

... Figure 38. V 2.10 Exp. 1.70 1.30 0.90 0.50 -50 75 100 125 o C) Figure 40. V 0.60 0.50 0.40 0.30 0.20 -50 75 100 125 o C) Figure 42 IR21141/IR22141SSPbF Exp. - 100 o Temperature ( C) FLTCLR Logic Input Voltage vs. IL Temperature - 100 o Temperature ( C) SD Logic Input Voltage vs. Temperature IH Exp. -25 ...

Page 25

... OH www.irf.com 2.40 2.00 1.60 1.20 0.80 75 100 125 - Figure 44 Exp 100 125 - Exp -50 75 100 125 IR21141/IR22141SSPbF Exp. - 100 o Temperature ( C) SYFLT Logic Input Voltage vs. Temperature IL - 100 o Temperature ( C) Figure 46 vs. Temperature OL - 100 o Temperature ( C) Figure 48 vs. Temperature OL © 2009 International Rectifier 125 125 ...

Page 26

... C) Figure 50. V 8.30 7.60 6.90 6.20 5.50 -50 75 100 125 C) Figure 52 Exp 100 125 - Figure 54. FAULT/SD Open Drain Resistance vs. 26 IR21141/IR22141SSPbF - 100 o Temperature ( C) DSH Input Voltage vs. Temperature DSH+ Exp. - 100 o Temperature ( C) DSH Input Voltage vs. Temperature DSH- - 100 o Temperature ( ...

Page 27

... C) Figure 56. DTL Off Deadtime vs. Temperature 780 660 540 Exp. 420 300 -50 75 100 125 C) Figure 58. TonH Propagation Delay vs. Temperature Exp -50 75 100 125 C) Figure 60. TrH Turn On Rise Time vs. Temperature 27 IR21141/IR22141SSPbF - 100 o Temperature ( C) - 100 o Temperature ( C) - 100 o Temperature ( C) © 2009 International Rectifier ...

Page 28

... C) Figure 62. TonL Propagation Delay vs. Temperature 100 125 - Figure 64. TrL Turn On Rise Time vs. Temperature 6 5 Exp 100 125 - IR21141/IR22141SSPbF Exp. - 100 o Temperature ( C) Exp. - 100 o Temperature ( C) - 100 o Temperature ( C) Figure 66. t vs. Temperature DSA T1 © 2009 International Rectifier 125 ...

Page 29

... Exp 100 125 - Exp 100 125 - 1.80 1.45 1.10 0.75 0.40 -50 75 100 125 o C) Figure 72. IO2+H SC Pulsed Current vs. Temperature 29 IR21141/IR22141SSPbF - 100 o Temperature ( C) Figure 68. t vs. Temperature DSA T3 - 100 o Temperature ( C) Figure 70. t vs. Temperature SSH Exp. - 100 o Temperature ( C) © 2009 International Rectifier 125 ...

Page 30

... C) Figure 74. IO-H SC Pulsed Current vs. Temperature 900 700 Exp. 500 300 100 75 100 125 - 3.00 2.50 2.00 Exp. 1.50 1.00 -50 75 100 125 o C) Figure 78. IO1+H SC Pulsed Current vs. Temperature 30 IR21141/IR22141SSPbF - 100 o Temperature ( C) - 100 o Temperature ( C) Figure 76. t vs. Temperature ON1H - 100 o Temperature ( C) © 2009 International Rectifier ...

Page 31

... Exp. 100 75 100 125 - Figure 82. I Exp. -50 - Temperature ( C) Figure 83. I Logic "0" Input Bias Current vs. LIN- Temperature 31 IR21141/IR22141SSPbF - 100 o Temperature ( C) Logic "1" Input Bias Current vs. HIN+ Temperature - 100 o Temperature ( C) Logic "1" Input Bias Current vs. LIN+ Temperature 100 125 © ...

Page 32

... Case Outline www.irf.com IR21141/IR22141SSPbF © 2009 International Rectifier 32 ...

Page 33

... IR21141/IR22141SSPbF Max 0.476 0.161 0.641 0.299 0.334 0.342 n/a 0.062 A Max 13.001 0.844 0.519 0.096 4.015 0.881 0.830 0.724 ...

Page 34

... ORDER INFORMATION 24-Lead SSOP IR21141SSPbF 24-Lead SSOP IR22141SSPbF 24-Lead SSOP Tape & Reel IR21141SSPbF 24-Lead SSOP Tape & Reel IR22141SSPbF WORLDWIDE HEADQUARTERS: 233 Kansas Street, El Segundo, CA 90245 Tel: (310) 252-7105 http://www.irf.com www.irf.com IR21141/IR22141SSPbF This part has been qualified per industrial level Data and specifications subject to change without notice ...

Related keywords