BTS716GB

Manufacturer Part NumberBTS716GB
DescriptionIC HISIDE PWR SWITCH 4CH PDSO-20
ManufacturerInfineon Technologies
TypeHigh Side
BTS716GB datasheet
 


Specifications of BTS716GB

Input TypeNon-InvertingNumber Of Outputs4
On-state Resistance110 mOhmCurrent - Output / Channel2.6A
Current - Peak Output6.5AVoltage - Supply5.5 V ~ 40 V
Operating Temperature-40°C ~ 150°CMounting TypeSurface Mount
Package / CaseDSO-20Switch TypeHigh Side
Power Switch FamilyBTS716GBInput Voltage-10 to 16V
Power Switch On Resistance110mOhmOutput Current2.3A
MountingSurface MountSupply Current1.9mA
Package TypeDSOOperating Temperature (min)-40C
Operating Temperature (max)150COperating Temperature ClassificationAutomotive
Pin Count20Power Dissipation3.6W
Lead Free Status / RoHS StatusLead free / RoHS CompliantOther namesBTS716GB
BTS716GBNT
BTS716GBT
BTS716GBTR
BTS716GBXT
SP000014327
SP000272337
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
Page 1/16

Download datasheet (315Kb)Embed
Next
Smart High-Side Power Switch
BTS716GB
Product Summary
Package
P-DSO-20
PG-DSO20
Block Diagram
Data Sheet
1
V1.0, 2007-05-13

BTS716GB Summary of contents

  • Page 1

    ... Data Sheet Smart High-Side Power Switch Ω Ω Ω  Block Diagram 1 BTS716GB Package P-DSO-20 PG-DSO20 V1.0, 2007-05-13 ...

  • Page 2

    ... IN4 Data Sheet control and protection circuit of channel 2 control and protection circuit of channel 3 control and protection circuit of channel 4 2 Smart High-Side Power Switch BTS716GB V1.0, 2007-05-13 ...

  • Page 3

    ... ST3/4 open drain, low on failure 2 GND1/2 Ground of chip 1 (channel 1,2) 6 GND3/4 Ground of chip 2 (channel 3,4) Data Sheet Smart High-Side Power Switch Pin configuration (top view GND1/2 2 IN1 3 ST1/2 4 IN2 5 GND3/4 6 IN3 7 ST3/4 8 IN4 BTS716GB • OUT1 17 OUT2 OUT3 13 OUT4 V1.0, 2007-05-13 ...

  • Page 4

    ... IN: ST require an external current limit for the GND and status pins (a 150Ω bb(AZ) 2 (one layer, 70µm thick) copper area for Smart High-Side Power Switch BTS716GB Symbol Values L(lim ...

  • Page 5

    ... I one channel active: L(NOM) I L(GNDhigh 90 OUT 10 OUT off = 12 Ω / OUT Ω / OUT L 2 (one layer, 70µm thick) copper area for Smart High-Side Power Switch BTS716GB Values min typ max -- -- Values min typ max -- 110 140 -- 210 280 -- 2.3 2 ...

  • Page 6

    ... T jt ∆ T require an external current limit for the GND and status pins (a 150Ω bb(AZ) ON(CL) 6 Smart High-Side Power Switch Values min typ max 5 3 0.5 0.9 -- 1.9 3 6 150 -- -- table of protection functions and V1.0, 2007-05-13 BTS716GB Unit µ µ ° ...

  • Page 7

    ... IN(off IN(on +1.6 mA +1.6 mA Smart High-Side Power Switch Values min typ -- -- bb -- 600 ON 1.7 2.8 OUT(OL) 1 2.5 4 IN(T+) 1.0 -- IN(T-) -- 0.2 IN( 5.4 -- ST(high ST(low) V1.0, 2007-05-13 BTS716GB Unit max 4.0 V 6.0 kΩ 2 —s 20 —s -- —s 500 —s 20 µA 20 µ 0.6 ...

  • Page 8

    ... L, if potential at the Output exceeds the OpenLoad detection voltage 19 Data Sheet Chip 1 IN1 IN2 Chip 2 IN3 IN4 Channel 1 ( Channel 2 ( both channel Channel 1 ( Channel 2 ( high impedance, potential depends on external circuit = 150 Ω single resistor GND1 GND2 8 Smart High-Side Power Switch BTS716GB OUT1 OUT2 ST1/2 OUT3 OUT4 ST3 ...

  • Page 9

    ... Open-load detection, OFF-state diagnostic condition: Open Load OUT < 375 Ω ST(ON) GND disconnect Any kind of load. In case high is V Due to V > GND 9 Smart High-Side Power Switch BTS716GB = 150 Ω typ., R GND Z2 OUT1...4 > typ.; IN low ≈ OUT IN IN(T+) = low signal available. ...

  • Page 10

    ... Energy stored in load inductance: While demagnetizing load inductance, the energy dissipated in PROFET with an approximate solution for R L > 0 Ω: · · Maximum allowable load inductance for a single switch off / j,start = 150° Ω [mH Smart High-Side Power Switch BTS716GB ^ · · · i (t) dt ...

  • Page 11

    ... Typ. on-state resistance high L R [mOhm] ON Typ. standby current , 9...34 V, IN1,2,3,4 = low EE RII [µA] bb(off) Data Sheet Smart High-Side Power Switch V [ [° BTS716GB V1.0, 2007-05-13 ...

  • Page 12

    ... Figure 2a: Switching a resistive load, turn-on/off time and slew rate definition: on Data Sheet Figure 2b: Switching a lamp: Figure 3a: Turn on into short circuit: shut down by overtemperature, restart by cooling off Heating up of the chip may require several milliseconds, depending on external conditions 12 Smart High-Side Power Switch BTS716GB V1.0, 2007-05-13 ...

  • Page 13

    ... Figure 4a: Overtemperature: Reset if T < Data Sheet Smart High-Side Power Switch Figure 5a: Open load: detection in OFF-state, turn on/off to open load Open load of channel 1; other channels normal operation Figure 6a: Status change after, turn on/off to overtemperature Overtemperature of channel 1; other channels normal operation 13 BTS716GB V1.0, 2007-05-13 ...

  • Page 14

    ... Index Marking 1) Does not include plastic or metal protrusions of 0.15 max per side 2) Does not include dambar protrusion of 0.05 max per side 14 Smart High-Side Power Switch 0.35 x 45˚ 1) -0.2 +0.8 0.4 ±0.3 GPS05094 Dimensions in mm V1.0, 2007-05-13 BTS716GB ...

  • Page 15

    ... Creation of the green datasheet. First page : Adding the green logo and the AEC qualified Adding the bullet AEC qualified and the RoHS compliant features Package page Modification of the package to be green. Data Sheet Smart High-Side Power Switch 15 BTS716GB V1.0, 2007-05-13 ...

  • Page 16

    ... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...