L6227PD STMicroelectronics, L6227PD Datasheet - Page 13

• Manufacturer Part Number: L6227PD
• Description: IC DRVR DUAL FULL BRDG 36PWRSOIC
• Manufacturer: STMicroelectronics
• Type: H Bridger

Specifications of L6227PD

• Input Type: Non-Inverting
• Number Of Outputs: 4
• On-state Resistance: 730 mOhm
• Current - Output / Channel: 1.4A
• Current - Peak Output: 2.8A
• Voltage - Supply: 8 V ~ 52 V
• Operating Temperature: -25°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 36-PowerSOIC
• Operating Supply Voltage: 8 V to 52 V
• Supply Current: 1.4 A
• Mounting Style: SMD/SMT
• For Use With: 497-6817 - EVAL BOARD FOR L6227Q
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-5348-5; L6227PD

NON-DISSIPATIVE OVERCURRENT PROTECTION
The L6227 integrates an Overcurrent Detection Circuit (OCD). This circuit provides protection against a short
circuit to ground or between two phases of the bridge. With this internal over current detection, the external cur-
rent sense resistor normally used and its associated power dissipation are eliminated. Figure 12 shows a sim-
plified schematic of the overcurrent detection circuit.
To implement the over current detection, a sensing element that delivers a small but precise fraction of the out-
put current is implemented with each high side power MOS. Since this current is a small fraction of the output
current there is very little additional power dissipation. This current is compared with an internal reference cur-
rent I
OCD comparator signals a fault condition. When a fault condition is detected, the EN pin is pulled below the turn
off threshold (1.3V typical) by an internal open drain MOS with a pull down capability of 4mA. By using an ex-
ternal R-C on the EN pin, the off time before recovering normal operation can be easily programmed by means
of the accurate thresholds of the logic inputs.
Figure 12. Overcurrent Protection Simplified Schematic
Figure 13 shows the Overcurrent Detection operation. The Disable Time t
ation can be easily programmed by means of the accurate thresholds of the logic inputs. It is affected whether by
C
bridge when an overcurrent has been detected depends only by C
C
should be chosen as big as possible according to the maximum tolerable Delay Time and the R
be chosen according to the desired Disable Time.
The resistor R
are respectively 100K
EN
EN
and R
is also used for providing immunity to pin EN against fast transient noises. Therefore the value of C
REF
. When the output current in one bridge reaches the detection threshold (typically 2.8A) the relative
EN
values and its magnitude is reported in Figure 14. The Delay Time t
EN
C or LOGIC
+5V
should be chosen in the range from 2.2K to 180K . Recommended values for R
R
C
EN
EN
and 5.6nF that allow obtaining 200 s Disable Time.
EN
A
40 TYP.
R
DS(ON)
TO GATE
LOGIC
OPEN-DRAIN
INTERNAL
POWER SENSE
COMPARATOR
1 cell
OCD
POWER DMOS
OVER TEMPERATURE
n cells
OUT1
I
1A
/ n
(I
1A
I
A
EN
REF
I
1A
+I
VS
2A
value. Its magnitude is reported in Figure 15.
+
) / n
A
I
2A
OUT2
DISABLE
I
2A
POWER DMOS
A
/ n
n cells
HIGH SIDE DMOSs OF
before recovering normal oper-
THE BRIDGE A
DELAY
D02IN1353
POWER SENSE
before turning off the
1 cell
EN
value should
EN
and C
L6227
13/22
EN
EN