BTS5210L Infineon Technologies, BTS5210L Datasheet

Page 1

... AEC qualified • Green product (RoHS compliant) Data Sheet Smart High-Side Power Switch Ω Ω Ω  Block Diagram 1 BTS5210L Package P-DSO-12 PG-DSO-12-9 V1.1, 2007-05-29 ...

Page 2

... Data Sheet control and protection circuit equivalent to channel 1 2 Smart High-Side Power Switch BTS5210L V1.1, 2007-05-29 ...

Page 3

... Output 1,2 protected high-side power output of channel 1 and 2. Design the wiring for the 10 OUT1 max. short circuit current Data Sheet Smart High-Side Power Switch Pin configuration (top view) • GND 1 IN1 2 ST1 3 IN2 4 ST2 heat slug 3 BTS5210L OUT1 OUT2 7 NC V1.1, 2007-05-29 ...

Page 4

... IN: ST require an external current limit for the GND and status pins (a 150Ω bb(AZ) 2 (one layer, 70µm thick) copper area for Smart High-Side Power Switch BTS5210L Symbol Values self-limited Load dump T -40 ...

Page 5

... I L(NOM L(GNDhigh 90 OUT 10 OUT off = 12 Ω / OUT Ω / OUT L 2 (one layer, 70µm thick) copper area for Smart High-Side Power Switch BTS5210L Values min typ max -- -- Values min typ max -- 110 140 -- 210 280 -- 55 70 1.8 2.4 -- 3.4 3 ...

Page 6

... T require an external current limit for the GND and status pins (a 150Ω bb(AZ) ON(CL) 6 Smart High-Side Power Switch Values min typ max 0.5 0.9 -- 1.0 1 6 150 -- -- table of protection functions and V1.1, 2007-05-29 BTS5210L Unit 10 µ 10) µ ° ...

Page 7

... IN(off IN(on +1.6 mA +1.6 mA Smart High-Side Power Switch Values min typ -- -- bb -- 600 ON 1.7 2.8 OUT(OL) 1 2.5 4 IN(T+) 1.0 -- IN(T-) -- 0.2 IN( 5.4 -- ST(high ST(low) V1.1, 2007-05-29 BTS5210L Unit max 4.0 V 6.0 kΩ 2 —s 20 —s -- —s 500 —s 20 µA 20 µ 0.6 ...

Page 8

... External R optional; single resistor R GND operating voltage potential at the Output exceeds the OpenLoad detection voltage 19 Data Sheet IN OUT high impedance, potential depends on external circuit = 150 Ω for reverse battery protection up to the max. GND 8 Smart High-Side Power Switch BTS5210L V1.1, 2007-05-29 ...

Page 9

... Open-load detection, OFF-state diagnostic condition: Open Load OUT < 375 Ω ST(ON) GND disconnect Any kind of load. In case high is V Due to V > GND 9 Smart High-Side Power Switch BTS5210L = 150 Ω typ., R GND Z2 OUT1 or OUT2 > typ.; IN low ≈ OUT IN IN(T+) = low signal available. ...

Page 10

... Energy stored in load inductance: While demagnetizing load inductance, the energy dissipated in PROFET with an approximate solution for R L > 0 Ω: · · Maximum allowable load inductance for a single switch off / j,start = 150° Ω [mH Smart High-Side Power Switch BTS5210L ^ · · · i (t) dt ...

Page 11

... Typ. on-state resistance high L R [mOhm] ON Typ. standby current , I 9...34 V, IN1,2 = low EERII [µA] bb(off) Data Sheet Smart High-Side Power Switch V [ [° BTS5210L V1.1, 2007-05-29 ...

Page 12

... Figure 2a: Switching a resistive load, turn-on/off time and slew rate definition: on Data Sheet Figure 2b: Switching a lamp: Figure 3a: Turn on into short circuit: shut down by overtemperature, restart by cooling off Heating up of the chip may require several milliseconds, depending on external conditions 12 Smart High-Side Power Switch BTS5210L V1.1, 2007-05-29 ...

Page 13

... Figure 4a: Overtemperature: Reset if T < Data Sheet Smart High-Side Power Switch Figure 5a: Open load: detection in OFF-state, turn on/off to open load Open load of channel 1; other channels normal operation Figure 6a: Status change after, turn on/off to overtemperature Overtemperature of channel 1; other channels normal operation 13 BTS5210L V1.1, 2007-05-29 ...

Page 14

... Data Sheet 1) 6.4 ±0.1 A 8˚ 0.1 0.1 12x 1 C Seating Plane +0.13 0.4 0. 5.1 ±0 Depth 1 6 7.8 ±0.1 (Heatslug) 14 Smart High-Side Power Switch 1) 7.5 ±0.1 B 8˚ C 0.7 ±0.15 (0.2) (4.4) 10.3 ±0.3 0.25 B Dimensions in mm V1.1, 2007-05-29 BTS5210L ...

Page 15

... Creation of the green datasheet. First page : Adding the green logo and the AEC qualified Adding the bullet AEC qualified and the RoHS compliant features Package page Modification of the package to be green. Data Sheet Smart High-Side Power Switch 15 BTS5210L V1.1, 2007-05-29 ...

Page 16

... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...