BTS441TG Infineon Technologies, BTS441TG Datasheet

Page 1

Smart Power High-Side-Switch One Channel: 20 mΩ Product Summary On-state Resistance R ON Operating Voltage V bb(on) Nominal load current I L(ISO) Current limitation I L(lim) • N channel vertical power FET with charge pump, ground referenced CMOS compatible input, ...

Page 2

Data sheet PROFET 2 BTS441T Rev. 1.11, 2008-12-09 ...

Page 3

Maximum Ratings °C unless otherwise specified j Parameter Supply voltage (overvoltage protection see page 4) Supply voltage for full short circuit protection T =-40 ...+150°C j Start Load dump protection 1) V LoadDump = 2 Ω, ...

Page 4

Electrical Characteristics Parameter and Conditions at T =-40...+150° unless otherwise specified j bb Load Switching Capabilities and Characteristics On-state resistance (V bb (pin3) to OUT (pin5) ≥ see ...

Page 5

Parameter and Conditions at T =-40...+150° unless otherwise specified j bb Protection Functions 10) Current limit (pin (see timing diagrams, page 9) Repetitive short circuit current limit (see timing diagrams, ...

Page 6

Parameter and Conditions at T =-40...+150° unless otherwise specified j bb Input 14) Input resistance Input turn-on threshold voltage Input turn-off threshold voltage Input threshold hysteresis Off state input current (pin 2) On state input current ...

Page 7

Terms Input circuit (ESD protection) The use of ESD zener diodes as voltage clamp at DC conditions is not recommended. Inductive and overvoltage output clamp V clamped typ. ON Data sheet Overvolt. and reverse batt. protection V ...

Page 8

V disconnect with charged inductive bb load For inductive load currents up to the limits defined (max. ratings and diagram on page 8) each switch is protected against loss Consider at your PCB ...

Page 9

Typ. on-state resistance high L R [mΩ] ON Typ. standby current , I RII M = 9...34 V, IN1,2 = low bb I ...

Page 10

Timing diagrams Figure 1a: V turn on: bb proper turn on under all conditions Figure 2a: Switching a resistive load, turn-on/off time and slew rate definition: on Data sheet Figure 2b: Switching a lamp, Figure 3a: Short circuit shut down ...

Page 11

Package Outlines 0...0.3 0...0. Typical All metal surfaces tin plated, except area of cut. figure 5: PG-TO220-5-11 Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government ...

Page 12

C 0...0.15 1) Typical Metal surface min 7.25 12.3 All metal surfaces tin plated, except area of cut. Figure 6: PG-TO220-5-12 Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products ...

Page 13

Typical Metal surface min 7.25 6.9 All metal surfaces tin plated, except area of cut. Figure 7: PG-TO263-5-2 Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally ...

Page 14

Revision History Revision Date Changes 1.11 2008-12-09 RoHS-compliant PG-TO220 and PG-TO263 packages version of the BTS441T All pages: Infineon logo updated Page 1: Added “AEC qualified” and “RoHS” logo, added “Green Product (RoHS compliant)” and “AEC qualified” statement to feature ...

Page 15

... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...