BTS5240G Infineon Technologies, BTS5240G Datasheet
BTS5240G
Specifications of BTS5240G
BTS5240GT
BTS5240GXT
SP000014567
SP000308363
Available stocks
Related parts for BTS5240G
BTS5240G Summary of contents
Page 1
Smart High-Side Power Switch Two Channels 25m IntelliSense Product Summary Operating voltage V bb(on) Active channels On-state resistance R Nominal load current I L(nom) Current limitation Low I L(SCr) High General Description N channel vertical power MOSFET with ...
Page 2
Functional diagram GND overvoltage protection internal logic voltage supply IN1 ESD IS1 CLA IN2 IS2 current limit gate control + charge pump clamp for inductive load temperature sensor openload detection current sense Channel 1 control and protection circuit equivalent to ...
Page 3
Pin definition and function Pin Symbol Function 4 IN1 Input 1,2 activates channel1,2 in case of logic high signal 7 IN2 5 IS1 Diagnostic feedback 1 & channel 1,2 On state: advanced current sense with defined signal in ...
Page 4
Maximum Ratings at T =25°C, unless otherwise specified j Parameter Supply voltage (overvoltage protection see page 6) Supply voltage for full short circuit protection; T Maximum voltage across DMOS 3) Load dump protection V LoadDump In = low or high; ...
Page 5
Electrical Characteristics Parameter and Conditions -40...+150 ° 9... Thermal Resistance junction - soldering point 1) junction - ambient Load Switching Capabilities and Characteristics On-state resistance (V to OUT °C, ...
Page 6
Electrical Characteristics Parameter and Conditions -40...+150 ° 9... Load Switching Capabilities and Characteristics 1) Turn-on time to 90 Turn-off time to ...
Page 7
Electrical Characteristics Parameter and Conditions -40...+150 ° 9... Operating Parameters Off-State output current (included each channel IN 1) Operating current per active channel ...
Page 8
Electrical Characteristics Parameter and Conditions -40...+150 ° 9... Diagnostic Characteristics Open load detection voltage 1) Internal output pull down V = 13.5 V OUT Current sense ratio, static on-condition ...
Page 9
Electrical Characteristics Parameter -40...+150 ° 9... Diagnostic Characteristics Status invalid after negative input slope Status invalid after positive input slope with open load 1) Input Feedback Input resistance (see circuit page 11) ...
Page 10
Truth Table - for each of the two channels Normal Operation Current 2) Limitation Short circuit to GND Overtemperature Short circuit Open load = " Low" Level Z = high impedance, potential depends on external circuit L ...
Page 11
Input circuit ( ESD protection ), IN1 or IN2 ESD- GND The use of ESD zener diodes as voltage clamp at DC conditions is not recommended. Sense-Status output, IS1 or IS2 ON-State: Normal operation: ...
Page 12
Reverse battery protection OUT1 or OUT2 ...
Page 13
Maximum allowable load inductance for a single switch off (one channel 150° jstart bb 1000 100 [A] L Typ. on-state resistance ...
Page 14
Timing diagrams All channels are symmetric and consequently the diagrams are valid for channel 1 and channel 2. Figure 1a: Switching a resistive load, change of load current in on-condition OUT OUT ...
Page 15
Figure 2a: Switching a lamp Figure 2b: Switching a lamp with current limit: The behaviour of I and V is shown for resistor, which refers to curve ...
Page 16
Figure 4a: Overtemperature Reset < The behaviour and shown for a resistor, which refers to curve 1 in figure 1c delay(fault ...
Page 17
... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system ...