ISO1H811G Infineon Technologies, ISO1H811G Datasheet
ISO1H811G
Specifications of ISO1H811G
Available stocks
Related parts for ISO1H811G
ISO1H811G Summary of contents
Page 1
...
Page 2
... ISO1H811G Revision History: 2009-05-28 Previous Version: V1.1 V2.0 Final Datasheet V2.1 Data for parallel channels and UL approval added Edition 2009-05-28 Published by Infineon Technologies AG, Am Campeon 1-12, 85579 Neubiberg, Germany Infineon Technologies AG 2009. © All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics ...
Page 3
... DC applications • Driver for solenoid, relays and resistive loads Description The ISO1H811G is a galvanically isolated 8 bit data interface in PG-DSO-36 package that provides 8 fully protected high-side power switches that are able to handle currents up to 625 mA bit parallel µC compatible interface allows to connect the IC directly to a µ ...
Page 4
... Pin Configuration and Functionality Vbb N.C. 1 TAB VCC 2 DIS DIAG 14 GNDCC 15 N.C. 16 N.C. 17 TAB N.C. 18 Vbb Figure 1 Power SO-36 (430mil ISOFACE ISO1H811G 36 OUT0 35 OUT0 34 OUT1 33 OUT1 32 OUT2 31 OUT2 30 OUT3 29 OUT3 28 OUT4 27 OUT4 26 OUT5 25 OUT5 24 OUT6 23 OUT6 22 OUT7 21 OUT7 20 N.C. 19 GNDbb Version 2.1, 2009-05-28 ...
Page 5
... DIS signal, till new information is written into the input register. Current Sink to GNDCC. CS (Chip select) The system microcontroller selects the ISO1H811G by means of the low active pin CS to activate the parallel interface. By connecting the CS pin and WR pin to ground the parallel direct control is activated. Current Source to VCC ...
Page 6
... Blockdiagram Figure 2 Blockdiagram Datasheet Isolation Galvanic 6 TM ISOFACE ISO1H811G Blockdiagram Version 2.1, 2009-05-28 ...
Page 7
... Functional Description 3.1 Introduction The ISOFACE ISO1H811G includes 8 high-side power switches that are controlled by means of the integrated parallel interface. The interface is 8bit µC compatible. Furthermore a direct control mode can be selected that allows the direct control of the outputs OUT0...OUT7 by means of the inputs D0...D7 without any additional logic signal ...
Page 8
... The output stage at pin DIAG has an open drain functionality combined with a current source. DIAG t t Figure ISOFACE ISO1H811G Functional Description Normal Output short to GND operation I L(SCp) I L(SCr) Short circuit in on-state, shut down down by overtemperature, restart by cooling ...
Page 9
... WR have to be connected both to ground. 3.5.1 Parallel Interface Signal Description CS - Chip select. The system microcontroller selects the ISO1H811G by means of the CS pin. Whenever the pin logic low state, data can be transferred from the µC. CS High to low transition: • Parallel input data can be written in from then on CS Low to high transition: • ...
Page 10
... This unit decides wether the transmitted data is valid or not. If four times serial data coming in from the internal registers is not accepted, the output stages are switched off until the next valid data is received. Datasheet t WHCS t WRPW OUT0 - OUT7 10 TM ISOFACE ISO1H811G Functional Description t CSD t on/off Version 2.1, 2009-05-28 ...
Page 11
... P tot 3) single Loaddump = 13. 27V A V ESD V ESD , each channel ISOFACE ISO1H811G Electrical Characteristics are internally galvanic isolated. bb Ω resistor in GNDbb connection. Limit Values min. max. -0.5 6 -0.5 6.5 -0.5 6.5 -0.5 6.5 -0.5 6.5 -0.5 6.5 self limited ...
Page 12
... I L(NOM t off dV/dt on -dV/dt off 12 ISOFACE ISO1H811G Electrical Characteristics Limit Values Unit Test Condition typ. max. 1.5 50 K/W 38 Limit Values Unit Test Condition typ. max. 150 200 270 320 mΩ ...
Page 13
... I GNDL I L(off) ) bb(off 2.5 CC(under) V CC(u_rst) ∆V CC(under) I CC(uvlo) I CC(on) 13 ISOFACE ISO1H811G Electrical Characteristics Limit Values Unit Test Condition typ. max. kV/µs ∆ ISO A/m IEC61000-4-8 10.5 11 0 < ...
Page 14
... I L(SCr ON(CL bb(AZ 135 jt ∆T jt Symbol min. I diagsink = 135° diagsource 14 ISOFACE ISO1H811G Electrical Characteristics Limit Values Unit Test Condition typ. max. A 1.9 1.4 1.1 1.1 1 °C Limit Values Unit Test Condition typ ...
Page 15
... Limit Values min. typ. WRPW CSWR WHCS CSD 15 TM ISOFACE ISO1H811G Electrical Characteristics Unit Test Condition max. 0 0.3 mV µA 170 µs 230 Unit Test Condition max. ns Version 2.1, 2009-05-28 ...
Page 16
... For Qualification Report please contact your local Infineon Technologies office! Datasheet Symbol min Value 500 ISO 1250 2.6 2.6 0.01 16 ISOFACE ISO1H811G Electrical Characteristics Limit Values Unit Test Condition typ. max. V 1 45 1.2 Unit Conditions minute duration acc ...
Page 17
... Datasheet Electrical Characteristics 17 TM ISOFACE ISO1H811G Version 2.1, 2009-05-28 ...
Page 18
... Datasheet Electrical Characteristics 18 TM ISOFACE ISO1H811G Version 2.1, 2009-05-28 ...
Page 19
... Figure 12 PG-DSO-36 Datasheet 1.1 ±0.1 15.74 ±0.1 (Heatslug) 0.65 36x +0.13 0.25 0. 45˚ 1) 15.9 ±0.1 A (Mold) 19 ISOFACE ISO1H811G Package Outlines ±0. 2.8 6.3 0.1 C (Mold) 14.2 ±0.3 Bottom View 13.7 -0.2 (Metal) Version 2.1, 2009-05- Heatslug 0.95 ±0.15 0.25 B Heatslug ...
Page 20
... Geben Sie uns die Chance, hohe Leistung durch umfassende Qualität zu beweisen. Wir werden Sie überzeugen Published by Infineon Technologies AG Quality takes on an allencompassing significance at Semiconductor Group. bestmöglichen For us it means living up to each and every one of your demands in the best possible way ...