LTC4412IS6#TRPBF Linear Technology, LTC4412IS6#TRPBF Datasheet - Page 8

IC CTRL LOWLOSS PWRPATH TSOT23-6

LTC4412IS6#TRPBF

Manufacturer Part Number
LTC4412IS6#TRPBF
Description
IC CTRL LOWLOSS PWRPATH TSOT23-6
Manufacturer
Linear Technology
Series
PowerPath™r
Datasheet

Specifications of LTC4412IS6#TRPBF

Applications
Handheld/Mobile Devices
Fet Type
P-Channel
Number Of Outputs
1
Internal Switch(s)
No
Delay Time - On
110µs
Delay Time - Off
13µs
Voltage - Supply
2.5 V ~ 28 V
Current - Supply
16µA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
TSOT-23-6, TSOT-6
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC4412IS6#TRPBFLTC4412IS6#TRMPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC4412IS6#TRPBF
Manufacturer:
LT/凌特
Quantity:
20 000
LTC4412
APPLICATIO S I FOR ATIO
V
Since the analog controller’s thresholds are small (±20mV),
the V
way to avoid unwanted I • R drops in the power path. Both
pins are protected from negative voltages.
GATE Pin Usage
The GATE pin controls the external P-channel MOSFET
connected between the V
current is supplied by the power source at V
mode of operation, the internal current source, which is
responsible for pulling the GATE pin up, is limited to a few
microamps (I
rents exceed this, the GATE pin voltage will reach the
clamp voltage (V
current sink, which is responsible for pulling the GATE pin
down, has a higher current capability (I
auxiliary supply input pulling up on the SENSE pin and
exceeding the V
enters the reverse turn-off mode and a much stronger
current source is available to oppose external leakage
currents and turn off the MOSFET (V
While in forward regulation, if the on resistance of the
MOSFET is too high to maintain forward regulation, the
GATE pin will maximize the MOSFET’s V
clamp voltage (V
between the higher of V
Status Pin Usage
During normal operation, the open-drain STAT pin can be
biased at any voltage between ground and 28V regardless
of the supply voltage to the LTC4412. It is usually con-
nected to a resistor whose other end connects to a voltage
source. In the forward regulation mode, the STAT pin will
be open (I
auxiliary supply is connected to that input, and the voltage
on SENSE is higher than V
in the reverse turn-off mode. During this mode of opera-
tion the STAT pin will sink 10μA of current (I
will result in a voltage change across the resistor, depend-
ing on the resistance, which is useful to turn on an auxiliary
P-channel MOSFET or signal to a microcontroller that an
auxiliary power source is connected. External leakage
8
IN
and SENSE Pin Usage
IN
and SENSE pin connections should be made in a
S(OFF)
G(SRC)
IN
GON
). When a wall adaptor input or other
GON
pin voltage by 20mV (V
U
). If external opposing leakage cur-
) and V
). The clamping action takes place
IN
IN
U
IN
or V
and SENSE pins when the load
DS
+ 20mV (V
will be smaller. The internal
SENSE
W
GOFF
and the GATE pin.
RTO
G(SNK)
GS
RTO
).
), the system is
to that of the
S(SNK)
), the device
U
). With an
IN
. In this
). This
currents, if significant, should be accounted for when
determining the voltage across the resistor when the STAT
pin is either on or off.
Control Pin Usage
This is a digital control input pin with low threshold
voltages (V
as 1V. During normal operation, the CTL pin can be biased
at any voltage between ground and 28V, regardless of the
supply voltage to the LTC4412. A logical high input on this
pin forces the gate to source voltage of the primary
P-channel MOSFET power switch to a small voltage (V
This will turn the MOSFET off and no current will flow from
the primary power input at V
so that the drain to source diode is not forward biased. The
high input also forces the STAT pin to sink 10μA of current
(I
amples on using the STAT pin. A 3.5μA internal pull-down
current (I
input if the pin should be open.
Protection
Most of the application circuits shown provide some
protection against supply faults such as shorted, low or
reversed supply inputs. The fault protection does not
protect shorted supplies but can isolate other supplies and
the load from faults. A necessary condition of this protec-
tion is for all components to have sufficient breakdown
voltages. In some cases, if protection of the auxiliary input
(sometimes referred to as the wall adapter input) is not
required, then the series diode or MOSFET may be elimi-
nated.
Internal protection for the LTC4412 is provided to prevent
damaging pin currents and excessive internal self heating
during a fault condition. These fault conditions can be a
result of any LTC4412 pins shorted to ground or to a power
source that is within the pin’s absolute maximum voltage
limits. Both the V
taken significantly below ground without current drain or
damage to the IC (see Absolute Maximum Voltage Limits).
This feature allows for reverse-battery condition without
current drain or damage. This internal protection is not
designed to prevent overcurrent or overheating of external
components.
S(SNK)
). See the Typical Applications for various ex-
CTL
IL,
) on the CTL pin will insure a logical low level
V
IH
) for use with logic powered from as little
IN
and SENSE pins are capable of being
IN
if the MOSFET is configured
GOFF
4412fa
).

Related parts for LTC4412IS6#TRPBF