LT3485EDD-2#TRPBF Linear Technology, LT3485EDD-2#TRPBF Datasheet - Page 10

IC CHARGER PHOTOFLASH 10-DFN

LT3485EDD-2#TRPBF

Manufacturer Part Number
LT3485EDD-2#TRPBF
Description
IC CHARGER PHOTOFLASH 10-DFN
Manufacturer
Linear Technology
Datasheet

Specifications of LT3485EDD-2#TRPBF

Applications
Photoflash Capacitor Charger, Xenon
Current - Supply
5mA
Voltage - Supply
1.7 V ~ 10 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
10-DFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LT3485EDD-2#TRPBFLT3485EDD-2
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LT3485EDD-2#TRPBFLT3485EDD-2#PBF
Manufacturer:
LT
Quantity:
5 000
Company:
Part Number:
LT3485EDD-2#TRPBFLT3485EDD-2#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LT3485EDD-2#TRPBF
Quantity:
722
Company:
Part Number:
LT3485EDD-2#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIO S I FOR ATIO
Table 1. Recommended Transformer Parameters
PARAMETER
L
L
N
V
I
R
R
LT3485-0/LT3485-1/
LT3485-2/LT3485-3
Choosing the Right Device
(LT3485-0/LT3485-1/LT3485-2/LT3485-3)
The only difference between the four versions of the
LT3485 is the peak current level. For the fastest possible
charge time, use the LT3485-3. The LT3485-1 has the
lowest peak current capability, and is designed for
applications that need a more limited drain on the
batteries. Due to the lower peak current, the LT3485-1 can
use a physically smaller transformer. The LT3485-0 and
LT3485-2 have a current limit in between that of the
LT3485-3 and the LT3485-1.
Transformer Design
The flyback transformer is a key element for any
LT3485-0/LT3485-1/LT3485-2/LT3485-3 design. It must
be designed carefully and checked that it does not cause
excessive current or voltage on any pin of the part. The
main parameters that need to be designed are shown in
Table 1.
The first transformer parameter that needs to be set is the
turns ratio N. The LT3485-0/LT3485-1/LT3485-2/LT3485-
3 accomplish output voltage detection by monitoring the
flyback waveform on the SW pin. When the SW voltage
reaches 31.5V higher than the V
halt power delivery. Thus, the choice of N sets the target
output voltage as it changes the amplitude of the reflected
voltage from the output to the SW pin. Choose N accord-
ing to the following equation:
10
SAT
PRI
LEAK
ISO
PRI
SEC
N
=
V
OUT
31 5 .
+ 2
NAME
Primary Inductance
Primary Leakage Inductance
Secondary: Primary Turns Ratio
Secondary to Primary Isolation Voltage
Primary Saturation Current
Primary Winding Resistance
Secondary Winding Resistance
U
U
BAT
W
voltage, the part will
U
TYPICAL RANGE
100 to 300
LT3485-0
8 to 12
>500
<300
>1.6
<40
>5
where V
in the numerator is used to include the effect of the voltage
drop across the output diode(s).
Thus for a 320V output, N should be 322/31.5 or 10.2. For
a 300V output, choose N equal to 302/31.5 or 9.6.
The next parameter that needs to be set is the primary
inductance, L
formula:
where V
former turns ratio. I
1 (LT3485-2) and 2 (LT3485-3).
L
that the LT3485-0/LT3485-1/LT3485-2/LT3485-3 has ad-
equate time to respond to the flyback waveform.
All other parameters need to meet or exceed the recom-
mended limits as shown in Table 1. A particularly impor-
tant parameter is the leakage inductance, L
power switch of the LT3485-0/LT3485-1/LT3485-2/
LT3485-3 turns off, the leakage inductance on the pri-
mary of the transformer causes a voltage spike to occur
on the SW pin. The height of this spike must not exceed
40V, even though the absolute maximum rating of the SW
Pin is 50V. The 50V absolute maximum rating is a DC
blocking voltage specification, which assumes that the
current in the power NPN is zero. Figure 3 shows the SW
voltage waveform for the circuit of Figure 8 (LT3485-0).
PRI
L
TYPICAL RANGE
needs to be equal or larger than this value to ensure
PRI
200 to 500
LT3485-1
8 to 12
OUT
OUT
>500
<500
>0.8
>10
<80
V
is the desired output voltage. The number 2
is the desired output voltage. N is the trans-
OUT
PRI
. Choose L
N I
200 10
PK
TYPICAL RANGE
PK
200 to 500
is 1.4 (LT3485-0), 0.7 (LT3485-1),
LT3485-2
8 to 12
>500
<400
>1.0
<60
>7
PRI
9
according to the following
TYPICAL RANGE
100 to 300
LT3485-3
8 to 12
>500
<200
>3.5
<30
>2
LEAK
. When the
34850123fb
UNITS
mΩ
µH
nH
V
A

Related parts for LT3485EDD-2#TRPBF