ISL6532BCR-T Intersil, ISL6532BCR-T Datasheet - Page 7

• Manufacturer Part Number: ISL6532BCR-T
• Description: IC REG/CTRLR ACPI DUAL DDR 20QFN
• Manufacturer: Intersil

Specifications of ISL6532BCR-T

• Applications: Memory, DDR/DDR2 Regulator
• Current - Supply: 5.25mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 20-QFN
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Voltage - Supply: -

LGATE (Pin 19)
LGATE drives the lower (synchronous) FET of the V
synchronous buck switching regulator. LGATE is driven
between GND and P12V.
FB (Pin 11) and COMP (Pin 12)
The V
control loop. FB is the negative input to the voltage loop error
amplifier. The positive input of the error amplifier is
connected to a precision 0.8V reference and the output of
the error amplifier is connected to the COMP pin. The V
output voltage is set by an external resistor divider
connected to FB. With a properly selected divider, V
be set to any voltage between the power rail (reduced by
converter losses) and the 0.8V reference. Loop
compensation is achieved by connecting an AC network
across COMP and FB.
The FB pin is also monitored for under and over-voltage
events.
VDDQ (Pins 5, 6)
The V
the regulated V
pins serve as inputs to the V
Reference precision divider. During S3 (Suspend to RAM)
state, the V
standby LDO.
VTT (Pins 3, 4)
The VTT pins should be connected together. During S0/S1
states, the VTT pins serve as the outputs of the V
regulator. During any sleep state, the V
disabled.
VTTSNS (Pin 7)
VTTSNS is used as the feedback for control of the V
regulator. Connect this pin to the V
point of desired regulation.
VREF_OUT (Pin 9)
VREF_OUT is a buffered version of V
reference voltage for the V
recommended that a minimum capacitance of 0.1µF be
connected between V
between VREF_OUT and GND for proper operation.
VREF_IN (Pin 10)
A capacitor, C
is required. This capacitor and the parallel combination of
the Upper and Lower Divider Impedance (R
time constant for the start up ramp when transitioning from
S3 to S0/S1/S2.
The minimum value for C
following equation:
C
SS
>
DDQ
DDQ
C
------------------------------------------------
10 2A R
VTTOUT
⋅
switching regulator employs a single voltage
pins should be connected externally together to
DDQ
SS
⋅
DDQ
⋅
pins serve as an output from the integrated
, connected between VREF_IN and ground
U
V
||
DDQ
R
output. During S0/S1 states, the V
L
DDQ
SS
TT
and VREF_OUT and also
TT
can be found through the
linear regulator. It is
7
regulator and to the V
TT
TT
output at the physical
TT
and also acts as the
regulator is
U
||R
L
), sets the
TT
DDQ
TT
DDQ
linear
TT
linear
DDQ
DDQ
can
ISL6532B
The calculated capacitance, C
capacitor bank on the V
reaching the current limit of the V
NCH (Pin 15)
NCH is an open-drain output that controls the MOSFET
blocking backfeed from V
states. A 2kΩ or larger resistor is to be tied between the 12V
rail and the NCH pin. Until the voltage on the NCH pin
reaches the NCH trip level, the PWM is disabled.
If NCH is not actively utilized, it still must be tied to the 12V
rail through a resistor. For systems using 5V dual as the
input to the switching regulator, a time constant, in the form
of a capacitor, can be added to the NCH pad to delay start of
the PWM switcher until the 5V dual has switched from
5VSBY to 5VATX.
PGOOD (Power Good) (Pin 14)
Power Good is an open-drain logic output that changes to a
logic low if the V
state. PGOOD will always be low in any state other than
S0/S1/S2.
S5# (Pin 17)
This pin accepts the SLP_S5# sleep state signal.
S3# (Pin 16)
This pin accepts the SLP_S3# sleep state signal.
Functional Description
Overview
The ISL6532B provides complete control, drive, protection
and ACPI compliance for a regulator powering DDR memory
systems. It is primarily designed for computer applications
powered from an ATX power supply. A 250kHz Synchronous
Buck Regulator with a precision 0.8V reference provides the
proper Core voltage to the system memory of the computer.
An internal LDO regulator with the ability to both sink and
source current and an externally available buffered reference
that tracks the V
termination voltage.
ACPI compliance is realized through the SLP_S3 and
SLP_S5 sleep signals and through monitoring of the 12V
ATX bus.
Initialization
The ISL6532B automatically initializes upon receipt of input
power. Special sequencing of the input supplies is not
necessary. The Power-On Reset (POR) function continually
monitors the input bias supply voltages. The POR monitors
the bias voltage at the 5VSBY and P12V pins. The POR
function initiates soft-start operation after the bias supply
voltages exceed their POR thresholds.
TT
DDQ
regulator is out of regulation in S0/S1/S2
output by 50% provides the V
TT
DDQ
rail in a controlled manner without
SS
to the input rail during sleep
, will charge the output
TT
LDO.
TT