ADM1032ARZ-001

Manufacturer Part NumberADM1032ARZ-001
DescriptionIC TEMP MON REMOTE/LOCAL 8-SOIC
ManufacturerON Semiconductor
ADM1032ARZ-001 datasheet
Product Change Notification
 


Specifications of ADM1032ARZ-001

FunctionTemp Monitoring System (Sensor)TopologyADC, Comparator, Multiplexer, Register Bank
Sensor TypeExternal & InternalSensing Temperature0°C ~ 100°C, External Sensor
Output TypeSMBus™Output AlarmYes
Output FanYesVoltage - Supply3 V ~ 5.5 V
Operating Temperature0°C ~ 100°CMounting TypeSurface Mount
Package / Case8-SOIC (3.9mm Width)Full Temp Accuracy+/- 1 C, +/- 3 C
Digital Output - Bus InterfaceSerial (2-Wire)Lead Free Status / RoHS StatusLead free / RoHS Compliant
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
Page 12/18

Download datasheet (205Kb)Embed
PrevNext
1
SCLK
SDATA
A6
START BY
MASTER
Figure 13. Writing a Register Address to the Address Pointer Register,
1
SCLK
A6
A5
A4
SDATA
START BY
MASTER
SERIAL BUS ADDRESS BYTE
Figure 14. Writing to the Address Pointer Register Only
19
SCLK
SDATA
A6
A5
A4
START BY
MASTER
SERIAL BUS ADDRESS BYTE
Figure 15. Reading Data from a Previously Selected Register
ALERT Output
The ALERT output goes low whenever an out−of−limit
measurement is detected, or if the remote temperature sensor
is open−circuit. It is an open drain and requires a pullup to
V
. Several ALERT outputs can be wire−OR’ed together
DD
so that the common line goes low if one or more of the
ALERT outputs goes low.
The ALERT output can be used as an interrupt signal to a
processor, or it can be used as an SMBALERT. Slave devices
on the SMBus can not normally signal to the master that they
want to talk, but the SMBALERT function allows them to do
so.
One or more ALERT outputs can be connected to a
common SMBALERT line connected to the master. When
the SMBALERT line is pulled low by one of the devices, the
following procedure occurs (see Figure 16).
9
A5
A4
A3
A2
A1
A0
R/W
ACK. BY
ADM1032
FRAME 1
SERIAL BUS ADDRESS BYTE
1
SCLK (CONTINUED)
D7
SDATA (CONTINUED)
then Writing Data to the Selected Register
9
1
A3
A2
A1
A0
R/W
D7
D6
ACK. BY
ADM1032
FRAME 1
1
A3
A2
A1
A0
R/W
D7
D6
ACK. BY
ADM1032
FRAME 1
MASTER
RECEIVES
SMBALERT
ALERT RESPONSE
START
1. SMBALERT is pulled low.
2. Master initiates a read operation and sends the
alert response address (ARA = 0001 100). This is
a general call address that must not be used as a
specific device address.
3. The device whose ALERT output is low responds
to the alert response address and the master reads
its device address. Since the device address is
http://onsemi.com
12
1
D6
D5
D4
D3
D2
D1
D0
D7
ACK. BY
ADM1032
FRAME 2
ADDRESS POINTER REGISTER BYTE
9
D6
D5
D4
D3
D2
D1
D0
ACK. BY
ADM1032
FRAME 3
DATA BYTE
9
D5
D4
D3
D2
D1
D0
ACK. BY
ADM1032
FRAME 2
ADDRESS POINTER REGISTER BYTE
9
D5
D4
D3
D2
D1
D0
ACK. BY
ADM1032
FRAME 2
DATA BYTE FROM ADM1032
DEVICE
NO
RD
ACK
ADDRESS
ADDRESS
ACK
MASTER SENDS
ARA AND READ
DEVICE SENDS
COMMAND
ITS ADDRESS
Figure 16. Use of SMBALERT
9
STOP BY
MASTER
STOP BY
MASTER
STOP BY
MASTER
STOP