GNM314R72A681KD01D Murata Electronics North America, GNM314R72A681KD01D Datasheet - Page 44

• Manufacturer Part Number: GNM314R72A681KD01D
• Description: CAP 4-ARRAY 680PF 100V X7R 1206
• Manufacturer: Murata Electronics North America
• Series: GNMr

Specifications of GNM314R72A681KD01D

• Capacitance: 680pF
• Voltage - Rated: 100V
• Dielectric Material: Ceramic
• Number Of Capacitors: 4
• Circuit Type: Isolated
• Temperature Coefficient: X7R
• Tolerance: ±10%
• Mounting Type: Surface Mount
• Package / Case: 1206 (3216 Metric)
• Height: 0.031" (0.80mm)
• Size / Dimension: 0.126" L x 0.063" W (3.20mm x 1.60mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 490-3419-2

7
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
42
No.
11
12
13
14
GNM Series Specifications and Test Methods (1)
Continued from the preceding page.
Vibration
Resistance
Resistance to
Soldering Heat
Deflection
Solderability of
Termination
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Appearance
Capacitance
Q/D.F.
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
No defects or abnormalities
Within the specified tolerance
30pF min.: QU1000
30pF max.:
C: Nominal
No cracking or marking defects should occur.
75% of the terminations are to be soldered evenly and
continuously.
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T2.5%
(Whichever is
larger)
30pF min.: QU1000
30pF max.:
C: Nominal
More than 10,000MΩ or 500Ω · F (Whichever is smaller)
No failure
Compensating Type
#GNMpp4
Capacitance (pF)
Capacitance (pF)
Temperature
GNM1M2
GNM212
GNM214
GNM314
QU400+20C
or T0.25pF
QU400+20C
Type
5.0
d
a
b
c
100
1.0
2.0T0.05
2.0T0.05
2.0T0.05
2.5T0.05
R7, R6: Within T7.5%
R7, R6
R7, R6
Char.
Char.
a
Specifications
Fig. 2
0.5T0.05
0.6T0.05
0.7T0.05
0.8T0.05
25V min.
25V min.
0.025
0.025
max.
max.
High Dielectric Type
#GNMpp2
b
5.0
0.035
0.035
d
max.
max.
a
b
0.32T0.05
16V
16V
0.5T0.05
0.3T0.05
0.4T0.05
c
c
100
1.0
0.035
0.035
max.
max.
10V
10V
0.32T0.05
0.5T0.05
0.2T0.05
0.4T0.05
t=0.8mm
(in mm)
d
max.
max.
6.3V
0.05
6.3V
0.05
Solder the capacitor to the test jig (glass epoxy board) in the
same manner and under the same conditions as (10). The
capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should
be traversed in approximately 1 minute. This motion should be
applied for a period of 2 hours in each of 3 mutually perpendic-
ular directions (total of 6 hours).
Solder the capacitor on the test jig (glass epoxy board) shown
in Fig. 2 using a eutectic solder.
Then apply a force in the direction shown in Fig. 3 for 5T1 sec.
The soldering should be done by the reflow method and should
be conducted with care so that the soldering is uniform and free
of defects such as heat shock.
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion). Preheat at
80 to 120°C for 10 to 30 seconds. After preheating, immerse in
eutectic solder solution for 2T0.5 seconds at 230T5°C or
Sn-3.0Ag-0.5Cu solder solution for 2T0.5 seconds at 245T5°C.
Preheat the capacitor at 120 to 150°C for 1 minute. Immerse
the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder
solution at 270T5°C for 10T0.5 seconds. Let sit at room
temperature for 24T2 hours, then measure.
• Initial measurement for high dielectric constant type
Perform a heat treatment at 150+0/-10°C for one hour and
then let sit for 24T2 hours at room temperature.
Perform the initial measurement.
R230
Capacitance meter
45
Test Method
20
Fig. 3
50
Continued on the following page.
45
Pressurize
Pressurizing
speed : 1.0mm/sec.
Flexure : V1
C02E.pdf
07.2.6