GNM314R72A102KD01D Murata Electronics North America, GNM314R72A102KD01D Datasheet - Page 45

• Manufacturer Part Number: GNM314R72A102KD01D
• Description: CAP 4-ARRAY 1000PF 100V X7R 1206
• Manufacturer: Murata Electronics North America
• Series: GNMr

Specifications of GNM314R72A102KD01D

• Capacitance: 1000pF
• Voltage - Rated: 100V
• Dielectric Material: Ceramic
• Number Of Capacitors: 4
• Circuit Type: Isolated
• Temperature Coefficient: X7R
• Tolerance: ±10%
• Mounting Type: Surface Mount
• Package / Case: 1206 (3216 Metric)
• Height: 0.031" (0.80mm)
• Size / Dimension: 0.126" L x 0.063" W (3.20mm x 1.60mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 490-3421-2

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
No.
15
17
16
Continued from the preceding page.
Temperature
Cycle
Humidity Steady
State
Humidity Load
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T2.5%
(Whichever is
larger)
30pF min.: QU1000
30pF max.:
C:Nominal
More than 10,000MΩ or 500Ω · F (Whichever is smaller)
No failure
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T5%
(Whichever is
larger)
30pF and over:
10pF and over,
30pF and below:
10pF and below:
C: Nominal
More than 1,000MΩ or 50Ω · F (Whichever is smaller)
No failure
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T7.5%
(Whichever is
larger)
30pF and over:
30pF and below:
C: Nominal
More than 500MΩ or 25Ω · F (Whichever is smaller)
No failure
Compensating Type
Capacitance (pF)
Capacitance (pF)
Capacitance (pF)
Temperature
QU100+10C/3
QU275+5C/2
or T0.25pF
QU400+20C
or T0.75pF
QU200+10C
or T0.5pF
QU350
QU200
R7, R6: Within T7.5%
R7, R6: Within T12.5%
R7, R6: Within T12.5%
R7, R6
R7, R6
R7, R6
Char.
Char.
Char.
Specifications
25V min.
25V min.
25V min.
0.025
max.
max.
max.
0.05
0.05
GNM Series Specifications and Test Methods (1)
High Dielectric Type
0.035
max.
16V
max.
max.
0.05
0.05
16V
16V
0.035
max.
10V
10V/6.3V
10V/6.3V
max.
max.
0.05
0.05
max.
6.3V
0.05
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as (10). Perform the five cycles
according to the four heat treatments listed in the following
table. Let sit for 24T2 hours (temperature compensating type)
or 48T4 hours (high dielectric constant type) at room
temperature, then measure.
• Initial measurement for high dielectric constant type
Sit the capacitor at 40T2°C and 90 to 95% humidity for 500T12
hours.
Remove and let sit for 24T2 hours at room temperature, then
measure.
Apply the rated voltage at 40T2°C and 90 to 95% humidity for
500T12 hours.
Remove and let sit for 24T2 hours at room temperature, then
measure.
The charge/discharge current is less than 50mA.
Perform a heat treatment at 150+0/-10°C for one hour and
then let sit for 24T2 hours at room temperature.
Perform the initial measurement.
Temp. (°C)
Time (min.)
Step
Temp. +0/–3
Operating
30±3
Min.
1
Test Method
Temp.
Room
2 to 3
Continued on the following page.
2
Temp. +3/–0
Operating
Max.
30±3
3
Temp.
Room
2 to 3
4
C02E.pdf
43
07.2.6
7