IC REG PWM STEP-DWN ADJ 8-SOIC

 

MAX750ACSA

Manufacturer Part NumberMAX750ACSA
DescriptionIC REG PWM STEP-DWN ADJ 8-SOIC
ManufacturerMaxim Integrated Products
TypeStep-Down (Buck), PWM - Current Mode
MAX750ACSA datasheets

Availability: In stock

International delivery:

Warranty: 60 days

Shipping & payment terms

Added to cart

Select quantity

 

Specifications of MAX750ACSA

Internal Switch(s)YesSynchronous RectifierNo
Number Of Outputs1Voltage - Output1.25 ~ 11 V
Current - Output450mAFrequency - Switching170kHz
Voltage - Input4 ~ 11 VOperating Temperature0°C ~ 70°C
Mounting TypeSurface MountPackage / Case8-SOIC (3.9mm Width)
Voltage - Supply4 V ~ 11 VFrequency-max210kHz
Duty Cycle92%Pwm TypeCurrent Mode
BuckYesBoostNo
FlybackNoInvertingNo
DoublerNoDividerNo
CukNoIsolatedNo
Lead Free Status / RoHS StatusContains lead / RoHS non-compliant  
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
Page 7/16

Download datasheet (207Kb)Embed
PrevNext
______________________________________________________________Pin Description
PIN
8-PIN
16-PIN
NAME
DIP/SO
WIDE SO
Shutdown—active low. Ground to power-down chip, tie to V+ for normal operation.
SHDN
1
2
Output voltage falls to 0V when SHDN is low.
Reference Voltage Output (+1.22V) supplies up to 100µA for external loads. Bypass to
2
3
REF
GND with a capacitor that does not exceed 0.047µF.
Soft-Start. Capacitor between SS and GND provides soft-start and short-circuit protec-
3
7
SS
tion. 510kΩ resistor from SS to SHDN provides current boost.
External voltage divider feedback point. When an external voltage divider is connected from
the output voltage to CC and GND, this pin becomes the feedback input for adjusting the
4
8
CC
output voltage. Connect a 330pF compensation capacitor between the output and CC.
5
9
I.C.
Internal Connection. Make no external connection to this pin.
6
10, 11
GND
Ground*
7
12, 13, 14
LX
Drain of internal P-channel power MOSFET*
Supply Voltage Input. Bypass to GND with 1.0µF ceramic and large-value electrolytic capaci-
8
1, 15, 16
V+
tors in parallel. The 1µF capacitor must be as close to the V+ and GND pins are possible.*
–
4, 5, 6
N.C.
No Connect—not internally connected.
*16-Pin Wide SO: All pins with the same name must be connected together externally.
_______________Detailed Description
The MAX750A/MAX758A switch-mode regulators use a
current-mode pulse-width-modulation (PWM) control
system coupled with a simple step-down (buck) regula-
tor topography. Input voltages range from 4V to 11V for
the MAX750A, and from 4V to 16V for the MAX758A.
The current-mode PWM architecture provides cycle-by-
cycle current limiting, improved load transient response
characteristics, and simpler outer-loop design.
The controller consists of two feedback loops: an inner
(current) loop that monitors the switch current via the
current-sense resistor and amplifier, and an outer (volt-
age) loop that monitors the output voltage through the
error amplifier (Figure 1). The inner loop performs
cycle-by-cycle current limiting, truncating the power-
transistor on-time when the switch current reaches a
predetermined threshold. This threshold is determined
by the outer loop. For example, a sagging output volt-
age produces an error signal that raises the threshold,
allowing the circuit to store and transfer more energy
during each cycle.
_______________________________________________________________________________________
Adjustable, Step-Down,
Current-Mode PWM Regulators
FUNCTION
Figures 1 and 2 show a capacitor and a resistor connect-
ed to the soft-start (SS) pin to ensure an orderly power-
up. Typical values are 0.1µF and 510kΩ. SS controls
both the soft-start timing and the maximum output cur-
rent that can be delivered while maintaining regulation.
The charging capacitor slowly raises the clamp on the
error-amplifier output voltage, limiting surge currents at
power-up by slowly increasing the cycle-by-cycle current-
limit threshold. The 510kΩ resistor sets the soft-start
clamp at a value high enough to maintain regulation, even
at currents exceeding 1A. This resistor is not necessary
for lower current loads. Refer to the Maximum Output
Current vs. Supply Voltage, No. R1 graph in the Typical
Operating Characteristics . Table 1 lists timing character-
istics for selected capacitor values and circuit conditions.
The overcurrent comparator trips if the load exceeds
approximately 1.5A. A soft-start cycle begins when
either an undervoltage or overcurrent fault condition
triggers an internal transistor to discharge the soft-
start capacitor to ground. A soft-start cycle also
begins at power-up and when coming out of the shut-
down mode.
Programmable Soft-Start
7

Related parts for MAX750ACSA

Part Number DescriptionManufacturer Datasheet
MAX750ACSA+  MAX750ACSA+ IC REG PWM STEP-DWN ADJ 8-SOIC Maxim Integrated Products
MAX750AESA+  MAX750AESA+ IC REG PWM ADJ 8-SOIC Maxim Integrated Products
  MAX750ACPA DC/DC Switching Regulators Adjustable PWM Step-Down Regulator Maxim Integrated Products
MAX750ACSA+T  MAX750ACSA+T IC REG PWM ADJ 8-SOIC Maxim Integrated Products
MAX750AESA+T  MAX750AESA+T IC REG PWM ADJ 8-SOIC Maxim Integrated Products
  MAX750AESA DC/DC Switching Regulators Adjustable PWM Step-Down Regulator Maxim Integrated Products
  MAX750AMJA DC/DC Switching Regulators Adjustable PWM Step-Down Regulator Maxim Integrated Products
  MAX750AEPA DC/DC Switching Regulators Adjustable PWM Step-Down Regulator Maxim Integrated Products
  MAX750AESA-T DC/DC Switching Regulators Adjustable PWM Step-Down Regulator Maxim Integrated Products
  MAX750ACSA-T DC/DC Switching Regulators Adjustable PWM Step-Down Regulator Maxim Integrated Products
  MAX750A-MAX758A Adjustable, Step-Down, Current-Mode PWM Regulators MAXIM [Maxim Integrated Products]
  MAX7501KN Maxim Integrated Products
  MAX750 Maxim Integrated Products
MAX7500MUA+T  MAX7500MUA+T IC TEMP SENSOR DIGIT 8-UMAX Maxim Integrated Products
MAX7500MSA+T  MAX7500MSA+T IC TEMP SENSOR DIGIT 8-SOIC Maxim Integrated Products